manualshive.com logo in svg

A-Link WL54AP, User Manual

Share
Download
A-Link WL54AP User Manual Download Page 4

 

4

Chapter 2: Preparing Your Network

 

․

Preparing Your Network 

In this chapter, you’ll learn what to do before configuring your router. 

Before you can configure your router, you need to set up all the computers on your network for 
TCP/IP networking. You also need to know certain information from your ISP. 

 

․

Configuring Windows for IP Networking 

You need to configure each computer in your network for TCP/IP networking. If you plan to use 
the DHCP feature (recommended), you should configure each computer to receive an IP 
address automatically. See the procedure below for instructions. 

 

If you don’t plan to use DHCP, you’ll need to manually assign an IP address to each computer. 
Refer to your Windows documentation for instructions on how to do this. 

 

To configure Windows to receive dynamic IP address: 

 

1. Click the 

Start 

button. Select 

Settings 

and click the 

Control Panel 

icon. Double-click the 

Network 

icon. 

2. On the Configuration tab, select the 

TCP/IP 

line for the applicable Ethernet adapter. Do not 

choose a TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL. If the word 

TCP/IP 

appears by itself, select that line. Click the 

Properties 

button. 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WL54AP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands