manualshive.com logo in svg

A-Link WL54AP, User Manual

Share
Download
A-Link WL54AP User Manual Download Page 26

 

26

․

DHCP 

Use the DHCP screen to set up your router as a Dynamic Host Configuration Protocol (DHCP) 
server. DHCP servers automatically assign IP addresses to all the clients on your network.   
The DHCP screen is shown in the figure below. 
 

 

 
To set up your router as a DHCP server: 
 

1. Make sure there is not already a DHCP server running on your network. 
 
2. Make sure that each computer on your network is configured to receive an IP address 

automatically. 

 
3. On the DHCP screen, click Enable. 
 
4. Type the IP Pool Starting Address. The address you specify will be the first IP address that can 

be assigned to a computer on the network. Type the IP Pool Ending Address. The address you 
specify will be the last IP address that can be assigned.   

 
5. Click Apply to put your changes in effect, or click Cancel to undo your changes. 
 

Display DHCP Table 

 
Click Display DHCP Table to launch the DHCP Active IP window. In this screen, the DHCP Active 
IP Table lists information about the computers that have been assigned IP addresses by the DHCP 
server. For each active client, the table shows: 

․

Index number 

․

Client Hostname 

․

IP Address 

․

Mac Address 

In addition, the DHCP Server IP Address is listed above the table.   
You can click Refresh to see the latest data. Close the window when you are finished looking at 
the table. The DHCP Active IP window is shown in the figure below. 

Summary of Contents for WL54AP














































Reviews:

No comments

Brands by name

Popular brands

Load more brands