RAPID TOASTER VCT-200
7
P/N 1010710 Rev. N 02/13
McDonald’s
Operating Instructions
1. Set the Bun Thickness Adjustment Controls
(Figure 2A and 2B) as follows:
• For 17 second toasters, set the Crown control to
5 = 13/16” (20.06 mm).
• For 10 second toasters, set the Crown control to
3 = 11/16” (17.4 mm).
• For 17 second toasters, set the Heel/Club control
to D = 9/16” (14.3 mm).
• For 10 second toaster, set the Heel/Club control
to B = 7/16” (11.1 mm).
2. Turn the Rocker Switch on (Figure 3). Allow 30
minutes warm-up time before proceeding.
NOTE: The temperature display (Figure 4) will flash
“LO” until preset operating temperature is reached.
When the toaster approaches the preset tempera-
ture, “USE” will appear in the temperature display
and the unit is ready to toast buns.
The toaster is tested and shipped with the heat-
ers set at a preset recommended temperature. If
“USE” does not appear in the window after warm-
up period, see Temperature Adjustments below for
recommended temperature settings and to adjust
temperature settings.
3. Drop buns into toaster (Figure 3). Cut sides of
heel and crown must face each other (heel/club
in front, crown in back).
4. Toasted product will drop into the bun landing
area (Figure 3).
5. Test at least 4 buns before putting toaster
into service.
6. Turn the rocker switch off when finished toasting.
Toaster Operation
The Rapid Toaster uses a platen heater and two aux-
iliary heaters. The platen heater consists of a heating
coil built into the platen to toast the cut side of the bun.
The two auxiliary heaters assist in providing additional
heat to the buns. The first auxiliary heater is located
within the conveyor belt/chain in the front of the toaster.
The second auxiliary heater is located within the
conveyor belt/chain at the rear of the unit.
TEMPERATURE CONTROL
NOTE: Setpoint Temperature refers to the desired
temperature setting.
OPERATION
5
3
2
1
6
4
CROWN
B
E
D
C
A
F
HEEL/CLUB
THICKNESS
THICKNESS
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
1 = 9/16” (14.3mm)
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
5
D
Figure 2A. Bun Thickness Adjustment Controls for
17 second toasters
NOTE: Background color of this label is YELLOW.
B
POW
ER
TEMP
DOW
N
TEM
P
UP
TEMP
SCALE
˚C
˚F
3
3
2
1
6
5
4
CROWN
B
E
D
C
A
F
HEEL/CLUB
THICKNESS
THICKNESS A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
1 = 9/16”(14.3mm)
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
CAU
TIO
N
Figure 3. Rapid Toaster
Bun Thickness
Adjustment Controls
Heel/Club
Crown
Bun Landing
Area
Power ON/OFF
Switch
Temperature Controls &
Temperature Display
3
5
2
1
6
4
C R OWN
B
E
B
C
A
F
HE E L /C L UB
T HIC K NE S S
T HIC K NE S S
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
1 = 9/16” (14.3mm)
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
3
B
Figure 2B. Bun Thickness Adjustment Controls for
10 Second Toasters
NOTE: Background color if this label is GRAY.
