RAPID TOASTER VCT-200
12
P/N 1010710 Rev. N 02/13
McDonald’s
Figure 11. Replacing Groovy Belt
Bun Feeder
Front (Heel) Conveyor Cover
Rear (Crown)
Conveyor Cover
Bun Chute
Safety
Interlock
Switch
(1 each side)
5
3
2
1
6
4
CROWN
B
E
D
C
A
F
HEEL/CLUB
THICKNESS
THICKNESS
A = 3/8” (09.5mm)
B = 7/16” (11.1mm)
C = 1/2” (12.7mm)
D = 9/16” (14.3mm)
E = 5/8” (15.9mm)
F = 11/16” (17.4mm)
1 = 9/16” (14.3mm)
2 = 5/8” (15.9mm)
3 = 11/16” (17.4mm)
4 = 3/4” (19.1mm)
5 = 13/16” (20.6mm)
6 = 7/8” (22.2mm)
5
D
Figure 12. Bun Thickness Adjustment Controls
MAINTENANCE (continued)
Monthly: Bun Temperature Test
NOTE: The minimum temperature allowed is 150º
F (65.6º C). If this temperature is not achieved con-
tact your Authorized Service Agency.
Tools Required:
Pyrometer/Needle probe attachment,
four 8 oz. coffee cups stacked together, plus one lid
or four 12 oz coffee cups plus one lid.
1. Turn the rocker switch (power ON/OFF) to ON
Preheat for 30 minutes.
2. Toast 3 regular buns to be used with the 8oz. cup
stack or 4 regular buns to be used with the 12 oz.
cup stack.
3. Immediately stuff the buns into the stacked cups
and tightly apply the lid.
4 Wait 10 minutes
5. Insert the needle probe attachment of the
pyrometer through the lid several times.
Note the
maximum
temperature.
Every Month: Replace Release Sheet
Every Three Months: Replace Groovy
Belt Wraps, Clean and Measure Conveyor
Belts/Chains, Check Roller Tensioners and
Check Temperature of Bun Landing Area.
Remove the Groovy Belt Wraps & Release Sheet
1. Turn the power On/Off rocker switch to OFF,
unplug the toaster and allow it to cool down.
2. Remove the Bun Feeder, Bun Chute, and change
the compression knob settings to “F & 6”
(Figure 12).
3. Remove and discard the black release sheet.
4. Open the Front (Heel/Club) conveyor cover and
rotate the Groovy Belt wrap so its’ flap is in the
middle (top to bottom) of the conveyor. Pull the
hinge pin out of the Groovy Belt and then remove
and discard this belt wrap. Repeat this process
on the Rear (Crown) side.
Clean the Conveyor Chain
1. Spray McD© All-Purpose Super Concentrate
(HCS) on a clean, dry, towel and wipe the surface
of the Rear (Crown) conveyor belt links firmly
from side to side and top to bottom. Immediately
repeat this procedure with a clean, dry, towel
dampened with KAYQUAT™ Sanitizer (HCS)
solution and repeat this procedure on the Front
(Heel/Club) conveyor belt.
2. Close the conveyor cover(s), plug the toaster in,
turn it on, count to ten (10) seconds for 10 sec-
ond toasters or seventeen (17) seconds for sev-
enteen second toasters. Next, turn the unit OFF
and unplug the power cord.
3. Open the conveyor cover(s) and repeat step #
1 to clean the other half of both the Front (Heel/
Club) and Rear (Crown) conveyor belts/chains.
CA
UT
ION
POW
ER
TEMP
DOW
N
TEMP
UP
TEM
P
SCAL
E
˚C
˚F
