manualshive.com logo in svg

a-eberle Low Voltage Regulation System, Installation Manual, Page: 61 / 64

Share
Download
a-eberle Low Voltage Regulation System Installation Manual Download Page 61

Page 59  

 

 

 

 

6.5.3

 

Operation of systems with LV fuse-switch-disconnectors 

 

DANGER! 

Risk of fatal injury from electric shock! 

Never partially open LV fuse switch disconnectors 

Operate the LV fuse switch disconnectors on the handle. 

 

 

 

Its intended that LV fuses are only used by qualified electricians or persons trained in elec-
trical  engineering eg: IEC 60269-2 or certified with respect to the local wiring and safety 
regulations applicable in your country. 
When switching the devices, the following must be observed: 

 

 

Ensure that commissioning, decommissioning and operation are only carried out by  

qualified electricians or persons trained in electrical engineering in accordance with 

VDE 0105-100. or certified with respect to the local wiring and safety regulations appli-

cable in your country. 

 

Ensure that only fuse links with silver-plated knives or silver-plated disconnection 

knives are used. 

 

Only operate LV fuse switch disconnectors by the operating handle. 

 

Always operate LV fuse switch disconnectors quickly. 

 

Figure 6-8 Operation fuse switch disconnector 

Summary of Contents for Low Voltage Regulation System

































































Reviews:

No comments