manualshive.com logo in svg

a-eberle Low Voltage Regulation System, Installation Manual, Page: 58 / 64

Share
Download
a-eberle Low Voltage Regulation System Installation Manual Download Page 58

Page 56  

 

 

 

We take care of it. 

 

 

Figure 6-5 Circuit breaker state OFF 

 

6.5.2

 

Operation of systems with switch disconnectors 

 

DANGER! 

Risk of fatal injury from electric shock! 

Never partially open the LV switch disconnector. 

Actuate the LV switch disconnector using the handle. 

 

 

 

Its intended that LV fuses are to be used only by qualified electricians or persons trained in 
electrical engingeering,eg IEC 60269-2 or certified with respect to the local wiring and safe-
ty regulations applicable in your country. 
 
When switching the devices, the following must be observed: 

 

 

Ensure that commissioning, decommissioning and operation are only carried out by  

qualified electricians or persons trained in electrical engineering in accordance with  

VDE 0105-100 or certified with respect to the local wiring and safety regulations appli-

cable in your country. 

 

Ensure that only fuse links with silver-plated knives or silver-plated disconnection 

knives are used. 

 

The switch disconnector must only be operated using the handle. 

 

Actuate the switch disconnector quickly. 

Summary of Contents for Low Voltage Regulation System

































































Reviews:

No comments