background image

19 

 

1.  Never  permit  children  to  play  with  or  operate  the  garage  door  opener  either  from  the  wall  station  or  the  remote 

controls.  Keep  radio  transmitter  locked  in  the  car.  Misuse  of  the  push  button  or  transmitter  could  result  in  serious 
injury or even death. 

 

2.  Open  the  garage  door  with  the  remote  controls  only  when  the  garage  door  is  fully  visible  to  you  and  clear  of  all 

obstructions. The garage door should be kept in sight until it is completely open or closed and you are certain that the 
garage door opener has shut off. 

 

3.  Attempting  to  exit  the  garage  through  the  garage  door  opening,  while  the  door  is  in  motion,  is  a  very  dangerous 

activity that could result in serious injury or even death. 

 

4. Children and pets should always be clear of the door opening while the garage door is in motion. 

 

5. Check the safety reverse mechanism at least once a month to make sure that it will reverse with the minimum amount 

of force. Also check to be sure that the door will reverse within 5cm of the floor. See p.14. 

 

6. Check the manual operation of your garage door at least every 90 days to be sure that it is operating smoothly and 

does  not  bind  or  stick.  Tighten  all  bolts  on  the  door  and  visually  check  all  hardware  including  springs  for  wear  of 
damage. 

Caution

: If service is needed contact your local garage door service person. 

 

7. Do not decrease the safety reversing sensitivity mechanism to overcome a damaged or poorly operating door. This 

will  adversely  affect  the  operation  of  the  safety  reverse  mechanism  which  could  result  in  damage  to  the  door, 
personal injury or even death. 

 

Caution: 

Never operate the door opener if the reversing mechanism is not functioning properly. 

 

8. Whenever possible, the manual disconnect should only be used when the door is fully closed. Caution: Extreme care 

must be taken whenever the disconnect cord is pulled with the door partially open. Weak or broken springs may allow 
the  door  to  fall  rapidly  resulting  in  property  damage,  personal  injury  or  death.  If  a  broken  spring  is  evident,  contact 
your  local  garage  door  service  person  immediately  before  disconnecting  the  door  from  the  opener.  Never  attempt 
servicing a broken spring. 

 

9. Always disconnect electrical power supply to the opener when performing any maintenance or service to the opener 

or garage door. Failure to do so could result in electrical shock, property damage, personal injury or death. 

 

10. If any damage to any  mechanical or structural component of the opener is observed, discontinue use and contact 

your local garage door service person immediately. 

 

11. If the door auto reverses, please ensure there is no obstruction to the track or door.  

After the Installation 

Summary of Contents for 4DS1























Reviews: