background image

 
What this warranty does not cover:

 

 

 

 

(a) 

Corrosion: Damage from salt, water or any other form of corrosion.  

(b) 

Installation: damage or defect due to faulty installation of the Product (except where installed by 4D Doors).  

(c) 

Service: damage or defect due to a failure to properly service, care for or maintain the Product in accordance with the 
instruction manual.  

(d) 

Damage due to misuse (including failure to follow the instruction manual) or deliberate, negligent or accidental damage of 
any sort.  

(e) 

Modifications: 4D Doors will not be required to incorporate any modifications made to existing or future models.  

(f) 

Electrical Power: Any damage, issues or faults caused by electrical surge or fluctuation. 

(g) 

Problems that are directly or indirectly caused by or relate to the garage door or garage door hardware, which could 
include but are not limited to door springs, rollers, curtain wear, fixings and alignment. 

(h) 

Normal wear and tear. 

(i) 

Non-authorised repairs. 

(j) 

Acts or omissions of any person, including approved dealers, other than 4D Doors and its staff. 

(k) 

Travel Expenses: Expenses incurred by 4D Doors or its authorised dealer in travelling and or transporting Products to 
and from the location of the Product are not included and will be paid for by the purchaser.  

(l) 

Additional access or equipment required: Expenses incurred by 4D Doors or its authorised dealer required to provide 
clear access, or the equipment used to access the Product (for example: Lifting hardware such as forklift or scissor lift) 
are not covered by this warranty and must be paid for by the purchaser.   

(m) 

Frequency Interference: Where remote transmitters cannot operate the opener due to frequency interference at the 
location where the Product is installed.  

(n) 

Damage due to matters outside of the reasonable control of 4D Doors including, but not limited to, rain, hail, flood, water, 
fire, insects or any other event beyond the reasonable control of 4D Doors.  

(o) 

Consumer Goods: Components such as globes, accessories, batteries and other consumable parts are not covered by 
this warranty.  

 

What will void this warranty:

 

 

 

 

4D Doors will be relieved of all obligations, responsibilities and liabilities under this warranty if, in the opinion of 4D Doors, the 
defects in the Product result from:   

 

 

 

(a)  Any modifications, repairs or works carried out to the Product which are not authorised by 4D Doors. 
(b)  The fitment of any device to the Product which is not approved by 4D Doors. 
(c)  Misuse or unreasonable use of the Product, as determined by 4D Doors. 
(d)  Any use of the Product other than for residential application only (i.e. for use in a single-family dwelling or individual 

garages within an apartment complex).  

(e)  Failure to follow any directions or instructions, including any warning notifications in instruction manuals or signs on or 

provided with the Product. 

 
 If any part of this warranty is or becomes illegal, void or unenforceable, this does not invalidate the rest of the warranty. 

 
How to make a claim

 

 

 

 

Please be aware you are responsible for the expense of making a claim under this warranty.  

 

 

 

To make a claim, if the Product was supplied to you directly from 4D Doors please forward a copy of your original receipt as 
proof of purchase and a completed warranty claim form to 4D Doors directly. If the Product was supplied by an authorised 4D 
Doors dealer, please provide the copy of your original receipt along with a completed warranty claim form to that dealer. If the 
authorised dealer cannot be contacted, then please contact 4D Doors and provide the copy of the receipt and the completed 
warranty claim form and 4D Doors will forward these to the relevant authorised dealer.    

 

 

This warranty is supplied by 4D Garage Doors Pty Ltd (ABN 96 659 631 559

at 

[email protected] 

 

 

WARRANTY CERTIFICATE 

Invoice No: 

 

Installation Date: 

  

Your Name: 

 

Phone No: 

  

Address: 

 

State: 

  

Installed by: 

 

Motor Serial #: 

 

Door Model: 

  

 

Please retain this completed warranty form along with your invoice as proof of purchase to validate you claim. 

 

 

Summary of Contents for 4DS1























Reviews: