background image

Installation Instruction and User Guide

1

IMPORTANT SAFETY RECOMMENDATIONS

WARNING

·

FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY

RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE.

·

PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION

RECOMMENDATIONS.

1. The opener is designed and manufactured to meet local regulations. The installer must be

familiar with local regulations required in respect of the installation of the opener.

2. Unqualified personnel or those persons who do not know the occupational health and

safety standards being applicable to automatic gates and other doors, must in no

circumstances carry out installations or implement systems.

3. Persons who install or service the equipment without observing all the applicable safety

standards will be responsible for any damage, injury, cost, expense or claim whatsoever

any person suffered as a result of failure to install the system correctly and in accordance

with the relevant safety standards and installation manual whether directly or indirectly.

4. For additional safety we strongly recommend the inclusion of Photo Beam. Although the

opener incorporates a pressure sensitive Safety Obstruction Force system the addition of

Photo Beam will greatly enhance the operating safety of an automatic garage door and

provide additional peace of mind.

5. Make sure that the garage door is fully open & stationary before driving in or out of the

garage.

6. Make sure the garage door is fully closed & stationary before leaving.

7. Keep hands and loose clothing off the opener and garage door all the time.

8. The Safety Obstruction System is designed to work on STATIONARY objects only.

Serious personal injury, death and / or property damage may occur if the garage door

comes into contact with a moving object

9.This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

10.

Waste electrical products should not be disposed of with household waste. Please

recycle where facilities exist. Check with your local authority or retailer for recycling

advice.

11. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a hazard.

12. Do not allow children to play with door controls. Keep remote controls away from children.

13. Watch the moving door and keep people away until the door is completely opened or

closed.

14. Take care when operating the manual release since an open door may fall rapidly due to

weak or broken springs, or being out of balance.

15. Frequently examine the installation, in particular check cables, springs and mountings for

signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a

fault in the installation or an incorrectly balanced door may cause injury.

16. Each month check that the drive reverses when the door contacts a 40mm high object

placed on the floor. Adjust if necessary and recheck since an incorrect adjustment may

present a hazard, for drives incorporating an entrapment protection system depending on

contact with the bottom edge of the door.

17. Disconnect the electric power when cleaning or carrying out other maintenance.

NOTE: If your garage has no service entrance door, we recommend an outside quick release

must be installed. This accessory allows manual operation of the garage door from outside in

case of power failure,.

Summary of Contents for 4DR2

























Reviews: