3Ware 3W-6800 - Escalade 6800 RAID Controller User Manual Download Page 118

Page: 118 / 174

3ware Escalade Storage Switch User Guide

108

www.3ware.com

Installing the storage switch while installing
SuSE Linux with YaST1

Materials required

•

3ware 3DM CD-ROM, 3ware driver installation disk for SuSE
Linux (1)

•

3ware driver installation disk.

•

SuSE Linux Installation CD-ROM/DVD and boot disk

Note:

We have tested systems where an IDE drive con-

nected to the motherboard interfered with using the
Escalade Storage Switch as a boot device. Disconnecting
the IDE drive while installing Linux will eliminate this
problem. After Linux is installed, the drive can be recon-
nected.

Create disk arrays

Refer to the 3ware Hardware Installation and 3ware Disk Array
Configuration Utility chapters.

Boot with the SuSE CD/DVD or diskette

1 Insert SuSE Boot diskette into the floppy drive of the computer.

If your BIOS supports it you may boot directly from the SuSE
installation CD-ROM/DVD disk instead.

2 Select the manual or YaST1 installation method. YaST2 is not

supported. If the system boots in YaST2 mode, select Abort and
continue the install from the main installation menu.

Summary of Contents for 3W-6800 - Escalade 6800 RAID Controller















































































































































































Search results

Summary of Contents for 3W-6800 - Escalade 6800 RAID Controller

Reviews:

Related manuals for 3W-6800 - Escalade 6800 RAID Controller

Brands by name

Popular brands

3Ware 3W-6800 - Escalade 6800 RAID Controller, User Manual

Search results

Summary of Contents for 3W-6800 - Escalade 6800 RAID Controller

Reviews:

Related manuals for 3W-6800 - Escalade 6800 RAID Controller

Brands by name

Popular brands