3T-Components 3T-MOTORS 3T35-10RB Installation & Operating Instructions Manual Download

Page: 18 / 24

1 x Press

Stop-button

1 x Press button

P2 / Set Up

Hold down Up- + Down-button

simultaneously

1 x Press button

P2 / Set Up

1 x Press button

P2 / Set Up

Pairing another handheld transmitter:

Beep from motor

+ down and up

1 x Press button

P2 / Set Up

Beep from motor

+ down and up

The motor confirms

the programming

with 3 beeps and

down and up

Handheld transmitter already paired

New handheld transmitter / not paired

The motor confirms

the programming

with 7 beeps and

down and up

1 x Press P1 button

3 x Beep

from motor

Note:

The endpoints must already be programmed

to be able to use this method.

1 x Press button

P2 / Set Up

Delete handheld transmitter:

Beep from motor

+ down and up

1 x Press button

P2 / Set Up

Beep from motor

+ down and up

The motor confirms

the programming

with 3 beeps and

down and up

Handheld transmitter already paired

Handheld transmitter to be deleted

1 x Press button

P2 / Set Up

Delete all handheld transmitter:

Beep from motor

+ down and up

1 x Press button

P2 / Set Up

Beep from motor

+ down and up

The motor confirms

the programming

with 3 beeps and

down and up

PROGRAMMING RADIO TRANSMITTER

3T-MOTORS Radio tubular motors

| Programming radio transmitter

Summary of Contents for 3T-MOTORS 3T35-10RB

























Search results

Summary of Contents for 3T-MOTORS 3T35-10RB

Reviews:

Related manuals for 3T-MOTORS 3T35-10RB

Brands by name

Popular brands

3T-Components 3T-MOTORS 3T35-10RB, Installation & Operating Instructions Manual

Search results

Summary of Contents for 3T-MOTORS 3T35-10RB

Reviews:

Related manuals for 3T-MOTORS 3T35-10RB

Brands by name

Popular brands