3T-Components 3T-MOTORS 3T35-10RB Installation & Operating Instructions Manual Download

Page: 1 / 24

Motor type 3T45-RB

(For shafts from 60 mm)

3T45-10RB
3T45-20RB
3T45-30RB
3T45-40RB

Motor type 3T35-RB

(For shafts from 40 mm)

3T35-10RB
3T35-13RB

www.3t-components.de

WEEE-Reg.-Nr.: DE 77028333

Smart Home Ready with everHome

Control via smart phone, tablet, PC or via
voice commands with Alexa or Google Assistant

INTELLIGENT

DRIVES &

CONTROLS

FOR SHUTTERS

AND AWNINGS

INSTALLATION &

OPERATING INSTRUCTIONS

Instructions and notes for installation and operation

3T-MOTORS Radio shutter / awning motors

with electronical limit switches

Attention:

It is important for the safety of persons
to follow these instructions.
Keep these instructions for future reference.

Summary of Contents for 3T-MOTORS 3T35-10RB

























Search results

Summary of Contents for 3T-MOTORS 3T35-10RB

Reviews:

Related manuals for 3T-MOTORS 3T35-10RB

Brands by name

Popular brands

3T-Components 3T-MOTORS 3T35-10RB, Installation & Operating Instructions Manual

Search results

Summary of Contents for 3T-MOTORS 3T35-10RB

Reviews:

Related manuals for 3T-MOTORS 3T35-10RB

Brands by name

Popular brands