manualshive.com logo in svg

3M 3M-Matic S-857, Instructions And Parts List

Share
Download
3M 3M-Matic S-857 Instructions And Parts List Download Page 2

i

Intended Use ...............................................................................................................................

1

Equipment Warranty and Limited Remedy ..................................................................................

2

S-857 Contents ...........................................................................................................................

2

Important Safeguards ..................................................................................................................

3 - 4

Specifications ..............................................................................................................................

5

Installation And Set-Up ................................................................................................................

6 - 9

Receiving and Handling ..............................................................................

6

Machine Set-Up ..........................................................................................

6

Mounting .....................................................................................................

6 - 7

Air Regulator/Filter/Lubricator .....................................................................

8

Tape Drum-Bracket Assembly .....................................................................

9

Theory of Operation ....................................................................................................................

10 - 14

General Information ....................................................................................

10

Operational Explanation ..............................................................................

11 - 13

       Rest Position, Air Off ............................................................................

11

       Rest Position, Air On ............................................................................

11

       Application Cycle, Cut/Buff Sequence ..................................................

12

       Application Cycle, Feed Sequence .......................................................

13

Components ................................................................................................

14

       Valves ...................................................................................................

14

       Cylinders ..............................................................................................

14

Operation .....................................................................................................................................

15 - 16

Tape Loading And Threading .......................................................................

15 - 16

Operating Sequence ....................................................................................

16

Adjustments .................................................................................................................................

17

Tape Width ...................................................................................................

17

Tape Web Alignment ....................................................................................

17

Tape Drum Tension ......................................................................................

17

Tape Tension Roller ......................................................................................

17

V-8 Valve Adjustment ...................................................................................

17

Air Flow Controls ..........................................................................................

17

Maintenance .................................................................................................................................

18

Blade Replacement ......................................................................................

18

Air Line Filter ................................................................................................

18

Air Line Lubricator ........................................................................................

18

Instruction Manual

S-857 “L” Clip Applicator
Type 29500

Table of Content

Page

Summary of Contents for 3M-Matic S-857














































Reviews:

No comments

Brands by name

Popular brands

Load more brands