3D Upfitters Ender 3 S1 Page 9 Installation Manual Download | Manualshive

Page: 9 / 23

background image

slot. Use a 14mm or 16mm cap head screw to attach the door.

Now that the latches are mounted, it is time to connect the strike plates. Each plate
has a squishy adhesive covering the same size as the plate. Carefully attach the
adhesive side to the acrylic at the location of each latch. Then, adjust the width of the
metal strike plate so that it is held on by the pressure of the two sides of the plate. The
adhesive covering will keep the metal strike plate from scratching the acrylic.

Copyright 2023 3D Upfitters LLC

9

«
...
7
8
9
10
11
...
»

Summary of Contents for Ender 3 S1
























Reviews:

No comments

Related manuals for Ender 3 S1

Brand: welland Pages: 2

Brand: Dixon Bayco Pages: 4

Brand: SCC Pages: 47

Brand: ZALMAN Pages: 10

Brand: hager Pages: 4

RocketStor 6414AS

Brand: HighPoint Pages: 4

Brand: Adicos Pages: 28

Brand: Interactive Pages: 7

Brand: IEI Technology Pages: 10

Brand: Tripp Lite Pages: 2

Brand: DAS Pages: 32

Brand: Raidon Pages: 25

Brand: Leviton Pages: 2

Thinstall TA500

Brand: CHIEF Pages: 12

Brand: CHIEF Pages: 12

Deep Silence 5 Rev. B

Brand: Nanoxia Pages: 18

Enthoo Evoly series

Brand: Phanteks Pages: 32

Brand: Icy Box Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands