3D Hobby Shop YAK55 Assembly Manual Download Page 4 | Manualshive

Page: 4 / 46

3D Hobby Shop YAK55 Assembly Manual Download Page 4

SAFETY in Flying

ALWAYS fly your aircraft in a safe area, away from spectators.

ALWAYS fly your aircraft in a safe manner, within your control.

NEVER fly too close to yourself.

ALWAYS wear eye protection while operating your model aircraft.

ALWAYS keep your hands and body clear of propellers.

ALWAYS observe lipoly battery safety procedures.

ALWAYS handle gasoline in a safe manner.

ALWAYS perform a ground test and range check of your radio system before flying.

REQUIRED ITEMS

Drill and drill bits
30 Minute Epoxy Glue (

NOT

5-minute Epoxy)

Hobby Knife
Phillips Screwdriver
Set Metric Allen Wrenches
Small Pliers
Wire Cutters
Rubbing Alcohol
Paper Towels
Blue Loctite thread-locking adhesive
Dremel-type rotary tool
Small adjustable wrench or wrench set

IMPORTANT NOTE:   3DHS Recommends ONLY High-Torque, Digital, Metal-gear Servos for this
aircraft.     Suitable   part   numbers   include   Futaba   BLS157hv   or  BLS172hv,   Hitec   HS-7955TG,   JR
8611A, and JR 8711A.  DO NOT attempt to use nylon-geared servos on this airplane.

THIS AIRCRAFT IS NOT A TOY! IT IS A HIGH PERFORMANCE AEROBATIC AIRCRAFT AND
IMPROPER SETUP AND/OR USE COULD RESULT IN INJURY OR DEATH.

Assembly Instructions

Unpacking

Unpack your airplane and examine the components.   Check for damage of any kind.   If you find any
damage, contact 3DHobbyShop and report the damage.   Shippers are not always kind to our planes but
we   do   our   best   to   make   the   situation   right   if   you   receive   a   damaged   item.     Please   contact   3dhs
immediately via email at:

[email protected]

or you can contact us via telephone at (717) 814-

5316. We do our best to answer or return phone calls but email may be a faster way to connect with us
depending on the time of year and our travel schedule.

Covering Seams

There are many seams in the covering on this aircraft where one color meets another.  We recommend
using a covering iron or trim sealing tool to go over all of the covering seams on your Yak.  This will help
to prevent any peeling of the covering.  Repeat this periodically.  For long term durability, particularly on
gasoline powered aircraft, you can seal edges and points on the covering with clear fingernail polish.

4

«
...
2
3
4
5
6
...
»

Summary of Contents for YAK55















































Reviews:

No comments