manualshive.com logo in svg

3D Hobby Shop YAK55, Assembly Manual, Page: 38 / 46

Share
Download
3D Hobby Shop YAK55 Assembly Manual Download Page 38

Wing Attachment

The wing attaches to the fuselage with one nylon thumb-screw per side.  

Your carbon-fiber wing tube is a snug fit into the wings and fuselage.  This provides additional strength
and   fatigue   resistance.    As   a   result,   you   may   need   to   periodically   lubricate   your   wing   tube.     We
recommend non-stick cooking spray or silicone spray-lube for this job.  Your wings will be an especially
snug fit onto the tube the first several times you install them.  Go slowly and patiently to prevent damage
the first several times. The wing  tubes typically loosen up with use so don’t panic if it is tight when the
plane is new.  Don’t forget to use clips or other methods to prevent aileron wires from coming unplugged
in flight and to properly restrain aileron wires so they will not be damaged from chafing with airframe
vibration.

Your 3dhs yak includes a pair of wing bags for storage.  In one wing bag you will find a sleeve for storing
the wing tube.  The other wing bag includes a pocket for storing the Side-Force-Generators (SFG’s).

38

Summary of Contents for YAK55















































Reviews:

No comments