manualshive.com logo in svg

3D Hobby Shop YAK55, Assembly Manual, Page: 3 / 46

Share
Download
3D Hobby Shop YAK55 Assembly Manual Download Page 3

Thank you for purchasing this 3DHobbyShop ARF RC aircraft.  If you have any issues, questions, 
concerns or problems during assembly, please contact our tech department at:

[email protected]

SAFETY in Assembly

During assembly of this aircraft, you will be asked to use sharp knives, hot irons, and hobby adhesives.
Please follow all safety procedures recommended by the manufacturers of the products you use, and
always follow these important guidelines:

ALWAYS protect your eyes when working with adhesives, knives, or tools, especially power tools.  Safety
glasses are the best way to protect your eyes.

ALWAYS protect your body, especially your hands and fingers when using adhesives, knives, or tools,
especially power tools.  Do not cut toward exposed skin with hobby knives.  Do not place hobby knives on
tables or benches where they can roll off or be knocked off.  

ALWAYS have a first-aid kit handy when working with adhesives, knives, or tools, especially power tools.  

ALWAYS keep hobby equipment and supplies out of the reach of children.

3

Summary of Contents for YAK55















































Reviews:

No comments