manualshive.com logo in svg

3D Histech Pannoramic 1000, User Manual

Share
Download
3D Histech Pannoramic 1000 User Manual Download Page 9

Pannoramic 1000 2.0 – User’s Guide

  Disconnect plug!

Remember to unplug the power cord before you open the Pannoramic 1000 
device.

  Warning!

Only connect external devices that are safety extra low voltage rated to the 
instrument to avoid the risk of electrical shock.

  Warning!

The Pannoramic 1000 does not include any special facilities to protect from 
samples with an etching, potentially infectious, toxic, radioactive or other 
health-damaging effect. You are under obligation to comply with all currently 
binding legislation, notably, national accident prevention rules when handling 
samples of this kind.

  Caution!

Dirt or dust may adversely impact the operating capability of the Pannoramic 
1000. For this reason, measures must be taken to eliminate such influences to a
maximum possible degree. During periods of non-use, the Pannoramic 1000 
must be protected with a dust cover. Check that power is turned off before you 
put the cover on.

  Crush hazard!

Never open the front door unless prompted accordingly by software. When you 
open the door at any other time, make sure not to reach with your hands into the 
instrument to avoid the risk of crushing your fingers.

  Warning!

The front door is equipped with an interlock switch. If the door is opened while a 
digitization process is running, the process will be stopped instantly.

  Warning!

A defective Pannoramic 1000 is not classified as domestic waste. It must be 
properly disposed in accordance with currently valid legal requirements.

  Warning!

The Pannoramic 1000 may not be operated by other than properly instructed 
persons. Operating personnel must be fully aware of the potential dangers 
which a particular field of application involves. The Pannoramic 1000 is a 
precision instrument which may suffer a significant reduction in operational 
functions or even physical destruction following intervention performed in any 
nonconforming manner.

  Caution!

Do not position the equipment so that it is difficult to operate and to 
disconnect the device if necessary.

  Note:

The safety level of the equipment after servicing will be identical with level of 
the original equipment.

May 23, 2019 – Rev. 1

3DHISTECH Ltd.

9(79)

Summary of Contents for Pannoramic 1000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands