3Com OfficeConnect Series User Manual Download Page 88 | Manualshive

Page: 88 / 129

background image

9

T

ROUBLESHOOTING

AND

M

AINTENANCE

This chapter explains how to isolate and solve problems encountered with the
ISDN LAN Modem. Problems may stem from incorrect option settings or improper
installation.

This chapter covers the following main topics.

■

Checking the basics

■

Monitoring the LEDs

■

Evaluating symptoms and solutions

■

Finding more information

■

Contacting technical support

■

Downloading firmware

■

Resetting the ISDN LAN Modem

■

Reviewing statistics

CAUTION:

There are no user-serviceable parts inside your ISDN LAN Modem.

Unauthorized opening of the unit will void the warranty.

Checking the Basics

Before you monitor the LEDs or refer to the section on symptoms and solutions,
check the following:

■

Verify that the cables are not physically damaged. If damage is apparent,
replace the cable.

■

Verify that you have a proper 10BASE-T Ethernet cable (8-pin to 8-pin)

■

Verify that the power cord is connected to the ISDN LAN Modem and an
electrical outlet.

■

Verify that the ISDN cable is properly connected to the ISDN LAN Modem
and the ISDN wall outlet.

The ISDN LAN Modem will not operate if connected to an analog telephone wall
jack. Make sure that the ISDN LAN Modem is connected directly into the ISDN wall
outlet without connection to any intermediate telephone equipment (an NT1
device is not required with the ISDN LAN Modem).

«
...
86
87
88
89
90
...
»

Summary of Contents for OfficeConnect Series


































































































































Reviews:

No comments

Related manuals for OfficeConnect Series

Brand: Panasonic Pages: 8

Brand: Targus Pages: 8

Brand: EtherCAT Pages: 74

Brand: Kramer Pages: 3

Brand: VENOM Pages: 2

Brand: Targus Pages: 8

WebLogic Server

Brand: BEA Pages: 294

Brand: Motorola Pages: 59

Brand: Motorola Pages: 6

Brand: Motorola Pages: 2

Brand: Motorola Pages: 2

Brand: Motorola Pages: 2

Brand: Motorola Pages: 30

Brand: Motorola Pages: 116

Brand: Motorola Pages: 2

Brand: Motorola Pages: 38

Brand: Motorola Pages: 10

Brand: Motorola Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands