3Com OfficeConnect Series User Manual Download | Manualshive

Page: 8 / 129

background image

A

BOUT

T

HIS

G

UIDE

About This Guide provides an overview of this guide, describes guide conventions,
and tells you where to look for specific information.

This guide describes how to install and configure the OfficeConnect ISDN LAN
Modem and provides descriptions of key applications and networking concepts.

Audience Description

This guide is intended for end users with no presumed level of expertise.

How to Use
This Guide

Table 1 shows where to find specific information in this guide.

Table 1

If you are looking for...

Turn to...

An overview of the ISDN LAN Modem

Chapter 1

An explanation of the ISDN LAN Modem’s key functionality

Chapter 2

A description of the ISDN LAN Modem’s hardware components

Chapter 3

Instructions on setting up TCP/IP

Chapter 4

Instructions for the typical configuring of the ISDN LAN Modem software

Chapter 5

Instructions for advanced configuration of the ISDN LAN Modem software

Chapter 6

Information on supplementary voice services

Chapter 7

Information on placing, receiving and disconnecting calls

Chapter 8

Information on troubleshooting and maintenance

Chapter 9

Background information on networking

Appendix A

Information on using the custom browser

Appendix B

ISDN LAN Modem factory default settings

Appendix C

Technical specifications for the ISDN LAN Modem

Appendix D

Instructions for ordering ISDN service for the ISDN LAN Modem

Appendix E

Definition of terms

Glossary

«
...
6
7
8
9
10
...
»

Summary of Contents for OfficeConnect Series


































































































































Reviews:

No comments

Related manuals for OfficeConnect Series

Brand: Hainbuch Pages: 72

Brand: Zonet Pages: 63

Brand: Sennheiser Pages: 1

Brand: Gateway Pages: 68

Brand: Lindy Pages: 2

Brand: Yealink Pages: 8

Brand: Ralink Pages: 36

Brand: National Instruments Pages: 119

Brand: VOLTCRAFT Pages: 2

Brand: BeachTek Pages: 2

Remote Supervisor Adapter

Brand: IBM Pages: 124

Brand: Aaronn Pages: 2

Brand: MSI Pages: 162

Brand: Mitsubishi Pages: 250

Brand: Roving Networks Pages: 8

PS-100 Bluetooth Printer Adapter

Brand: Hama Pages: 8

Brand: Improved Racing Pages: 12

Brand: Well Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands