3Com Impact IQ 3C882 User Manual Download

Page: 97 / 114

ECHNICAL

UPPORT

3Com provides easy access to technical support information
through the variety of services described in this appendix.

On-line Technical Services

3Com offers worldwide product support seven days a week,
24 hours a day, through the following on-line systems:

■

3Com Bulletin Board Service (3ComBBS)

■

World Wide Web site

■

3ComForum on CompuServe®

■

3ComFacts

automated fax service

3Com Bulletin Board Service

3ComBBS contains patches, software, and drivers for all
3Com products, as well as technical articles. This service is
available via modem or ISDN seven days a week, 24 hours
a day.

Access by Analog Modem

To reach the service by modem, set your modem to 8 data
bits, no parity, and 1 stop bit.

Summary of Contents for Impact IQ 3C882



















































































































Search results

Summary of Contents for Impact IQ 3C882

Reviews:

Related manuals for Impact IQ 3C882

Brands by name

Popular brands

3Com Impact IQ 3C882, User Manual

Search results

Summary of Contents for Impact IQ 3C882

Reviews:

Related manuals for Impact IQ 3C882

Brands by name

Popular brands