manualshive.com logo in svg

3Com Impact IQ 3C882, User Manual

Share
Download
3Com Impact IQ 3C882 User Manual Download Page 80

Placing the ISDN Order Through Your Telephone Company

A-4

AT&T 
5ESS 
Custom 
Switch 

To order ISDN service for the AT&T 5ESS Custom switch, 
supply the telephone company with the information 
provided in Table A-3. 

* The Directory Number, Circuit-switched Voice, and Circuit-switched Voice Limit 

parameters should be set to 2 to allow both analog ports to be used simultaneously. 
Otherwise, if those parameters are set to 1, the ISDN line can only place or receive one 
call at a time.

† FCO (also referred to as Additional Call Offering) allows you to receive an incoming call 

while a dual-channel Multilink PPP call is active. If you do not want this feature, which 
may cost extra, FCO is not required.

Table A-3   

Line Configuration for AT&T 5ESS Custom

Required Information

Specification

Line Type

Standard (2B+D) ISDN line with 
point-to-point configuration

Line Code

2B1Q 

Interface Type

U interface with an RJ-45 jack

Directory Numbers

2

*

Maximum Terminals

1

Maximum B Channels

2

Actual User

Yes

Circuit-switched Voice

2

*

Circuit-switched Voice Channel

Any

Circuit-switched Data

2

Circuit-switched Data Channel

Any

Terminal Type

A (Basic Terminal)

Display

Yes

Circuit-switched Voice Limit

2

*

Circuit-switched Data Limit

2

Voice or Data

Both

Call Appearance Preference

Idle

Flexible Call Offering (FCO)

Yes

†

Summary of Contents for Impact IQ 3C882



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands