3Com 4800G Series Configuration Manual Download Page 839 | Manualshive

Page: 839 / 1246

background image

Introduction to IPv6 ACL

839

IPv6 ACL Naming

When creating an IPv6 ACL, you can specify a unique name for it. Afterwards, you
can identify the IPv6 ACL by its name.

An IPv6 ACL can have only one name. Whether to specify a name for an ACL is up
to you. After creating an ACL, you cannot specify a name for it, nor can you
change or remove the name of the ACL.

n

The name of an IPv6 ACL must be unique among IPv6 ACLs. However, an IPv6 ACL
and an IPv4 ACL can share the same name.

IPv6 ACL Match Order

Similar to IPv4 ACLs, IPv6 ACLs are sequential collections of rules defined with
different matching parameters. The order in which a packet is matched against the
rules in an IPv6 ACL may affect how the packet is handled.

Like in IPv4 ACLs, the following two match orders are available in IPv6 ACLs:

■

config

: where rules are compared against in the order in which they are

configured.

■

auto

: where depth-first match is performed.

Depth-first match for a basic IPv6 ACL

The following shows how your switch performs depth-first match in a basic IPv6
ACL:

1

Sort rules by source IPv6 address wildcard first and compare packets against the
rule configured with a longer prefix in the source IPv6 address wildcard prior to
other rules.

2

If two rules are present with the same prefix length in their source IPv6 address
wildcards, compare packets against the rule configured first prior to the other.

Depth-first match for an advanced IPv6 ACL

The following shows how your switch performs depth-first match in an advanced
IPv6 ACL:

1

Sort rules by protocol range first, and compare packets against the rule with the
protocol carried on IPv6 specified prior to other rules.

2

If two rules are present with the same protocol range, look at source IPv6 address
wildcard in addition. Then, compare packets against the rule configured with a
larger prefix length in the source IPv6 address wildcard prior to the other.

3

If the prefix lengths in the source IPv6 address wildcards are the same, look at the
destination IPv6 address wildcards. Then, compare packets against the rule
configured with a larger prefix length in the destination IPv6 address wildcard prior
to the other.

4

If the prefix lengths in the destination IPv6 address wildcards are the same, look at
the Layer 4 port number (TCP/UDP port number). Then compare packets against
the rule configured with the lower port number prior to the other.

5

If the port numbers are the same, compare packets against the rule configured
first prior to the other.

The comparison of a packet against an ACL stops once a match is found. The
packet is then processed as per the rule.

«
...
837
838
839
840
841
...
»

Summary of Contents for 4800G Series































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 4800G Series

Brand: IBM Pages: 86

Brand: VAF instruments Pages: 56

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 2

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Enginko Pages: 19

IAR KickStart Kit TWR-K60N512-IAR

Brand: IAR SYSTEMS Pages: 8

Brand: APARIAN Pages: 2

XM24 Expansion Module

Brand: Avaya Pages: 5

Brand: Eicon Networks Pages: 32

Brand: H3C Pages: 3

HHM Series HHM2409

Brand: TDK Pages: 2

zoomno MSC-5578

Brand: BIIZZY Pages: 2

Brand: LUX LUMEN Pages: 41

Brand: Paradyne Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands