3Com 4800G Series Configuration Manual Download Page 591 | Manualshive

Page: 591 / 1246

background image

Configuring an MLD Snooping Policy

591

c

CAUTION:

Make sure that the MLD query interval is greater than the maximum

response time for MLD general queries; otherwise undesired deletion of IPv6
multicast members may occur.

Configuring Source IPv6

Addresses of MLD

Queries

This configuration allows you to change the source IPv6 address of MLD queries.

Follow these steps to configure source IPv6 addresses of MLD queries:

c

CAUTION:

The source IPv6 address of MLD query messages may affect MLD

querier election within the segment.

Configuring an MLD
Snooping Policy

Configuration

Prerequisites

Before configuring an MLD Snooping policy, complete the following tasks:

■

Enable MLD Snooping in the VLAN

Before configuring an MLD Snooping policy, prepare the following data:

■

IPv6 ACL rule for IPv6 multicast group filtering

■

The maximum number of IPv6 multicast groups that can pass the ports

Configuring an IPv6

Multicast Group Filter

On a MLD Snooping-enabled switch, the configuration of an IPv6 multicast group
filter allows the service provider to define limits of multicast programs available to
different users.

In an actual application, when a user requests a multicast program, the user’s host
initiates an MLD report. Upon receiving this report message, the switch checks the
report against the configured ACL rule. If the port on which the report was heard
can join this IPv6 multicast group, the switch adds an entry for this port in the MLD
Snooping forwarding table; otherwise the switch drops this report message. Any
IPv6 multicast data that fails the ACL check will not be sent to this port. In this
way, the service provider can control the VOD programs provided for multicast
users.

Configuring an IPv6 multicast group filter globally

Follow these steps to configure an IPv6 multicast group globally:

To do…

Use the command…

Remarks

Enter system view

system-view

-

Enter VLAN view

vlan

vlan-id

-

Configure the source IPv6
address of MLD general
queries

mld-snooping
general-query source-ip

{

current-interface

|

ipv6-address

}

Optional

FE80::02FF:FFFF:FE00:0001 by
default

Configure the source IPv6
address of MLD
multicast-address-specific
queries

mld-snooping
special-query source-ip

{

current-interface

|

ipv6-address

}

Optional

FE80::02FF:FFFF:FE00:0001 by
default

«
...
589
590
591
592
593
...
»

Summary of Contents for 4800G Series































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 4800G Series

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: Barracuda Networks Pages: 2

Brand: D-Link Pages: 100

Brand: D-Link Pages: 134

Brand: D-Link Pages: 187

Brand: D-Link Pages: 225

Brand: D-Link Pages: 31

Brand: D-Link Pages: 35

DES-1016D - Switch

Brand: D-Link Pages: 19

Brand: D-Link Pages: 107

AirPlusXtremeG DI-624

Brand: D-Link Pages: 5

Brand: D-Link Pages: 48

Brand: Hal Communications Pages: 25

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: H3C Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands