manualshive.com logo in svg

3Com 3CBLUG16A - Baseline Switch 2816, User Manual

Share
Download
3Com 3CBLUG16A - Baseline Switch 2816 User Manual Download Page 60

60

A

PPENDIX

 C: S

AFETY

 I

NFORMATION

Power Cord Set

This must be approved for the country where it will be 
used.

L'Information De Sécurité Importante

Veuillez lire à fond l'information de la sécurité suivante 
avant d'installer le Baseline Switch 2816-SFP/2824-SFP 
Plus.

AVERTISSEMENT: 

L’installation et la dépose de ce 

groupe doivent être confiés à un personnel qualifié.

■

Si vous entassez l’unité Switch avec les unités 
SuperStack 3 Hub, l’unité Baseline Switch 
2816-SFP/2824-SFP Plus doit être installée en dessous 
des unités Hub plus étroites.

■

Ne branchez pas votre appareil sur une prise secteur 
(alimentation électrique) lorsqu'il n'y a pas de 
connexion de mise à la terre (mise à la masse).

■

Vous devez raccorder ce groupe à une sortie mise à 
la terre (mise à la masse) afin de respecter les 
normes internationales de sécurité.

■

Le coupleur d’appareil (le connecteur du groupe et 
non pas la prise murale) doit respecter une 
configuration qui permet un branchement sur une 
entrée d’appareil EN60320/IEC 320.

■

La prise secteur doit se trouver à proximité de 
l’appareil et son accès doit être facile. Vous ne 
pouvez mettre l’appareil hors circuit qu’en 
débranchant son cordon électrique au niveau de 
cette prise.

■

L’appareil fonctionne à une tension extrêmement 
basse de sécurité qui est conforme à la norme 
IEC60950. Ces conditions ne sont maintenues que si 
l’équipement auquel il est raccordé fonctionne dans 
les mêmes conditions.

U.S.A. and 
Canada

■

The cord set must be UL-approved and CSA 
certified.

■

The minimum specifications for the flexible 
cord are:
No. 18 AWG
Type SV or SJ
3-conductor

■

The cord set must have a rated current 
capacity of at least 10 A.

■

The attachment plug must be an 
earth-grounding type with a NEMA 5-15P 
(15 A, 125 V) or NEMA 6-15P (15 A, 250 V) 
configuration.

Denmark

The supply plug must comply with Section 
107-2-D1, Standard DK2-1a or DK2-5a.

Switzerland

The supply plug must comply with SEV/ASE 
1011.

UK

■

The supply plug must comply with BS1363 
(3-pin 13-amp) and be fitted with a 5 A 
fuse which complies with BS1362.

■

The mains cord must be <HAR> or 
<BASEC> marked and be of type 
HO3VVF3GO.75 (minimum).

Europe

■

The supply plug must comply with CEE7/7 
(“SCHUKO”)

■

The mains cord must be <HAR> or 
<BASEC> marked and be of type 
HO3VVF3GO.75 (minimum).

Summary of Contents for 3CBLUG16A - Baseline Switch 2816









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands