2Wire MEMO2 WS.502 Manual Download Page 8 | Manualshive

Page: 8 / 35

2Wire MEMO2 WS.502 Manual Download Page 8

Manual WS.502 v1.5

2-Wire Energy Monitor

7

(a red cross means unavailable (v255,255,255,255), or
failed transfer)

The modules themselves have not yet been upgraded!
This should be done in menu

'MODULES'

Important:

During upgrading WS.502 or other modules there are
no logs possible !

Never interrupt voltage during upgrading!!

7. ENERGY PRICES

As already mentioned, we can also (approximate)
calculate what the daily energy consumption is and
put a price tag on it. When we know the cost for gas,
water electricity, we can fill it in the table below.
There are 2 tariffs for electricity (day and night
consumption). Everything has to be filled in euro
cents, so DO NOT use

DECIMALS!

"SEND"

after the values are filled in.

Note. You can always adjust tariff changes,
you can calculate every day what your
consumption cost was at the prompted rate,
and is thus also stored in the database. If you
fill in other values afterwards, that will no
longer have any effect on the
previouscalculations.

8. LOGIN

The last part of the SETTINGS is at the top, and is
certainly not insignificant:

login

–

password

LOGIN

: The WS.502 can work simultaneously with 4

users. Each user can choose a login name (max 16
characters), a password (always 4 digits) and a
language version.

Only logged in as an administrator, with password
'admin2-WIRE'

you can make changes

here

At the first start-up we see: '

USERS': 0

The administrator is not counted among the 4 users, it
usually only serves to adjust the configuration so that
the other users can't change it. (So don't sprinkle the
admin login name and password around) You can
never change the login name 'admin2-WIRE' or
'adminIP', but you can change the password (2015).

CHANGE THE ADMINISTRATOR'S PASSWORD:

At

'LOGIN

OLD'

and 'PASS

OLD',

type the current login

name (admin2-WIRE) and password.

At

'LOGIN NEW

' back 'admin2-WIRE', and at

'PASS

NEW

'

type your new password (4 digits)

Press

SEND PASS

to send the new data.

NEW USERS

The same applies to new users to be created:

At

LOGIN OLD

type 'loginold' and at PASS

OLD

'1234'

«
...
6
7
8
9
10
...
»

Summary of Contents for MEMO2 WS.502




































Reviews:

No comments