manualshive.com logo in svg

2Wire MEMO2 WS.502, Manual, Page: 29 / 35

Share
Download
2Wire MEMO2 WS.502 Manual Download Page 29

Manual WS.502 v1.5 

          

 

 

 

2-Wire Energy Monitor

 

 

28 

 

Na. A pulse counter on a RG.016, BC.002, 
EC.441, PC.080 module is set to zero if the 
voltage is interrupted. 

Na. The period of 1 day in SUBTOTALS is too 
small, especially if the start day is the day of 
configuration. 

Na. Check out at point 16below:AMR FILES 
EXPORT LOCALLY TO EXCEL 

16. LOG TO FTP SERVER 

Do you have your  own FTP server? Or do you have 
one available through your provider? Then you can 
get more out of the 2-WIRE web server! 

LOG TYPES

: The logs are in  

CSV

  format and the 

separator is a  

semicolon.

 The decimal-sign is  

comma.

 

There are 4 types of logs possible:

 

RT LOG

:  

RealTime logs of measured values : voltage, 
current, power W(), power(VA),Power Factor 
(PF), m3 water, m3 gas, litres of fuel, 
temperature, CO2,... 

The interval can be set from 5  minutes to  60  
minutes. (NO is not active) If active, the readings 
of all log modules are forwarded to the log server 
following 
the  interval. 

Which measurements are logged can be checked 
per log channel ! (This is done in the 
configuration of the modules) 

FileName: LOCATION NAME + L DATE + 
TIME + csv 

(vb Nieuwstraat18Aalst_RTLOG28082015_013003.csv)  

 

RT DAYLOG (AMR)

:  

You can also send 

all

 RealTime logs once a day. 

The interval of measurements can be set here 
from 1 minute to 60 minutes. In CSV format we 
see all log channels, with their corresponding 
measurements (as checked with RTlog) 

The CSV file is drawn up according to 
the

'AMR'

format (see EANDIS) 

Attention: A file with 32 log channels, each about 
5 measurement types (V-A-W-VA-PF) with an 
interval of 1 minute is about 1MB in size. 

The time when this file is sent on DAG+1  can be 
set per hour. 

Logging always starts from midnight to midnight. 

(vb Nieuwstraat18 

 

Aalst_AMR_28082015_0001.csv)

 

CONSUMPTION LOG: 

The usage(counter positions)  can also be logged at 
an interval of 5 minutes to 60 minutes and 
transmitted directly to the log server. Here one can 
see the consumption, broken down according to day 
and nightly rate.  (if any) 

If solar panels, this can also be displayed separately. 

(Vb Nieuwstraat18Aalst_PAYLOG28082015_013003.csv) 

CONSUMPTION DAYLOG (MMR) : 

Analogous the RT Daylog, but only consume, with 
an adjustable interval of 5 to 60 minutes, or 1 total 
log of 24h.    

The CSV file is set according to the

'MMR'

format 

(see EANDIS)The time when this file is sent can be 
set per hour. Logging always starts from midnight 
to midnight.  

(e.g Nieuwstraat18Aalst_MMR_28082015_013003.csv)

 

LOCATION NAME:  

this info is the file name, and also mentioned in 
the 'HEADER' of the file. 

 

EANNR:  

can be billing no, location no...  

Na. If the value EAN541 is entered here, all 
modules will have a second input line where 16 
digit EAN numbers can be entered. 

 

Summary of Contents for MEMO2 WS.502




































Reviews:

No comments