background image

 

Copyright 2Touch Technologies Limited 2007-2008. All rights reserved. 

Installing the 2Touch Audio (2Touch model 014) 

1.

 

Position anchor posts: 67mm from edge of board; 
265mm down from top edge of board.  Suspend 
speakers on anchor posts. 

2.

 

Line up speakers to be parallel to vertical edge of board.  
Position black screws to top brackets to prevent speaker 
twist. 

3.

 

Note cavity recess in bottom rear of each speaker, which 
can be used to conceal wiring and components if 
necessary. 

Installing the 2Touch Audio (2Touch model 015) 

The 2Touch Audio_015 speaker assembly is the standard 
assembly included with 2Touch packages.  It consists of 
an active (powered) speaker incorporating a stereo 
amplifier, plus a passive speaker.   

Compared to the model 014 solution, the 015 uses a 
smaller enclosure; has no USB connectivity, and features additional audio 
input on the front panel.  A wired remote mounted volume scroll permits the 
015 speaker assemblies to be mounted high. 

The image at left outlines the components in 
the 2TAudio_015 assembly….: 

A.

 

Active speaker 

B.

 

Passive speaker 

C.

 

Wired remote volume & off-switch 

D.

 

Brackets set & fasteners 

E.

 

Cable between speakers (3.5mm jack 
one end only) 

F.

 

RCA-RCA stereo input cable 

G.

 

RCA – 3.5mm audio stereo input cable 

Two brackets are supplied with each speaker. These (combined with 
appropriate wall anchors where necessary) support the 015 speakers on the 
wall, usually well away from the IWB itself, and generally high above areas 
where user contact might be likely. 

 

 

 

Summary of Contents for 2150 series



























Reviews: