2Touch 2150 series Installation Manual Download

Page: 5 / 26

Accessories for your 2Touch Board

Accompanying your 2Touch board is a wall mount kit containing four
aluminium angle brackets and fasteners to secure these to the wall.

If you have purchased the board is part of a “ready to install” pack, then the
following items are also included in the package:

Epson EB450We

Epson ultra short throw & bracket, 3000 lumens

Powered USB Hub

Powered 4 port USB hub

2T_MCS_1

Single gang Modular Connector System: fits three
snap-in modules (1 x USB-B, 1 x RCA-1, 1 x
VGA+3.5mm). Includes pre-terminated cables fixing
direct to faceplate: 5m VGA Cable; 5m RCA video;
3m 3.5mm Stereo mini; USB.

2T_Audio015

Wall Mounted Speakers with 30 Watt room amplifier.
One"active" speaker and one "passive". 2 audio
inputs. Wired remote volume control - wall mounted.

Depending on the order, various package upgrade options are available:

2T_MCS_1 to 2T_MCS_2

Upgrade connector system to dual gang

2T_Audio015 to
2T_Audio014

Upgrade speaker system to whiteboard speakers

Powered Hub to Cat5USBXtn

Upgrade usb connectivity solution to Cat5

Summary of Contents for 2150 series



























Search results

Summary of Contents for 2150 series

Reviews:

Related manuals for 2150 series

Brands by name

Popular brands

2Touch 2150 series, Installation Manual

Search results

Summary of Contents for 2150 series

Reviews:

Related manuals for 2150 series

Brands by name

Popular brands