2N SpeedRoute User Manual Download

Page: 51 / 101

Table of Programmable Parameters

3.2

WAN

Mode

Used for enabling the WAN port function on your gateway. If you enable the WAN

port, LAN1 is converted into WAN. There are three setting options:

Off

– disable the WAN function.

Static

– enable the WAN function. Set the fixed WAN IP address.

Useful especially when you use the cable or WiFi connection and know

the IP address assigned to you.

Dynamic

– enable the function to get setting from DHCP server. All

settings for network interface are received from DHCP server located in

connected network.

PPPoE

– enable the WAN function. Enter the login data to your

provider. Used mainly for the ADSL connection where you are assigned

the IP address by the provider after login authentication.

Caution

Important!

The static IP and PPPoE cannot be used at the same time.

Even if both the options are selected and saved in the database, the

option that is programmed is applied.

Static

Summary of Contents for SpeedRoute






































































































Search results

Summary of Contents for SpeedRoute

Reviews:

Related manuals for SpeedRoute

Brands by name

Popular brands

2N SpeedRoute, User Manual

Search results

Summary of Contents for SpeedRoute

Reviews:

Related manuals for SpeedRoute

Brands by name

Popular brands