SIGNAL FIRE GWDIN Interface Manual Download

Page: 1 / 33

Rev 1.15

SignalFire Telemetry

Interface Manual

DIN Mounted Gateway

SignalFire Part Numbers: GWDIN, GWDIN-ENET

The SignalFire DIN Gateway has the following features:

RS485 connection to Modbus client device

Optional Modbus-TCP Ethernet interface module

Wide range DC power input. 6 to 36VDC

Two open collector digital outputs

DIN rail mount

Collects and caches Modbus data from all SignalFire remote nodes

Provides configuration and status registers for remote configuration and status monitoring

RP-SMA antenna port for connection to external 900MHz antenna

Stores up to 4700 register values from any combination of remote nodes

Supports transparent Modbus mode

Internal Remote Shut Down (RSD) logic control option

Modbus register re-mapping

Remote configuration of SignalFire devices through an Ethernet gateway connection

Remote sensor configuration (PACTware and RadarMaster)

Radio is FCC and IC approved

AES 128bit Encryption

Class 1 Division 2 Area certification pending

Summary of Contents for GWDIN


































Search results

Summary of Contents for GWDIN

Reviews:

Related manuals for GWDIN

Brands by name

Popular brands

SIGNAL FIRE GWDIN, Interface Manual

Search results

Summary of Contents for GWDIN

Reviews:

Related manuals for GWDIN

Brands by name

Popular brands