2N OMEGA Lite User Manual Download Page 84

Page: 84 / 113

4.15. Firmware Updating

The firmware updating function helps you update the 2N

OMEGA Lite

Ethernet module firmware. Be sure to use the firmware supplied by the module
producer or the producer‟s technical support department only.

During firmware updating, new firmware versions with innovated functions are

downloaded.

The firmware file is named root.tgz.gpg and should have approximately 10

MB. The firmware updating process takes 5-10 minutes if you use your LAN and a
delay may occur due to a lower transmission rate if you use the Internet.

Click on the

Update firmware

item to update the firmware. The firmware

updating dialogue is displayed as shown below.

Push the

Browse

button to select the path to the firmware file and the

Update

button to upload the firmware file into the module.

Summary of Contents for OMEGA Lite


















































































































Search results

Summary of Contents for OMEGA Lite

Reviews:

Related manuals for OMEGA Lite

Brands by name

Popular brands

2N OMEGA Lite, User Manual

Search results

Summary of Contents for OMEGA Lite

Reviews:

Related manuals for OMEGA Lite

Brands by name

Popular brands