- 09 -
- 10 -
EN
DE
FR
ES
IT
EN
DE
FR
ES
IT
a. The receiver rings without the PIR sensor being
triggered.
The receiver may be matching on the same
frequency with nearby PIR sensors. You should
reset the pairing and re-pair your PIR sensors.
b. There is no ring/LED flash when the PIR sensor is
triggered.
• Check whether the batteries (AAA) are inserted
in the PIR sensor.
• If the receiver is powered by batteries, check
whether batteries (Type C batteries) are inserted
in the receiver.
• If the receiver is powered by an adapter, check
whether the power outlet being used for the
adapter is working properly.
• Check whether you have turned on the receiver.
• Pair the receiver and PIR sensor again.
c. The ringtone/alarm volume is greatly reduced.
A weak battery can reduce the ring volume.
Change the batteries every 10-12 months.
Metal constructions, walls, and other appliances
C. Selecting the notification mode:
The receiver will notify after the PIR sensor has
detected a car or someone passing by with a
chime/alarm sound, flashing LED, or chime/alarm
sound and flashing LED at the same time.
To select the notification mode, press the Sound
and Flash
button on the side of the receiver. The
receiver will display the current notification mode.
Keep pressing the Sound and Flash button and
stop when you have reached the preferred mode.
D: Pairing additional PIR sensors/receivers to the
alarm system:
Up to 5 PIR sensors can be paired with one
receiver. You can also extend the alarm system
with any number of receivers. This is only possible
when the PIR sensor and receiver are working on
the same frequency. Pair additional PIR sensors/re-
ceivers using the same pairing process as
described below.
The following pairing instructions are relevant to
receiver SKU O00QH-0512 and PIR sensor SKU
5. Trouble Shooting:
O00QH-0513
After the receiver and PIR sensor have been
powered, press the
Pairing button on the side of the
receiver. Next trigger the PIR sensor. If pairing is
successful, the receiver will play a ringing/alarm
sound. It normally takes about 30 seconds for the
PIR sensor and receiver to pair. If there is no
pairing within 30 seconds, the receiver will
automatically exit pairing mode. Please try pairing
again.
E: Resetting and re-pairing:
If the receiver rings but the PIR sensor has not
been triggered, or the PIR sensor interferes with
another receiver, it may be necessary to wipe the
current pairings and pair again.
For Resetting the PIR sensors, press the Pairing
button and hold for 5 seconds. The receiver will
ring and flash a LED, then all the PIR sensors
information will be deleted.
You can now re-pair the wanted PIR sensor.
F: Installation:
The PIR sensor and receiver can be mounted on a
wall or just put on a flat place.
To mount on a wall:
Select a suitable location for the receiver and PIR
sensor.
Drill holes on the wall. Next push the wall plugs
into the drilled holes and then insert the screws
into the wall plugs. Finally, mount the PIR
sensor/receivers on the screws.
Note:
• The recommended installation height for the PIR
sensor is 3.3-4.9ft (1.0-1.5m)
• The PIR sensor detecting angle is 45 degree and
detecting distance is 16.4-26.2ft (5-8m). Install
the PIR sensor in key monitoring areas such as
the entrance to a garage, store, or house.
• If installing the PIR sensor outside, note that
moving leaves and branches, strong wind, and
drastic changes in temperature can affect and
influence the sensor.
• The PIR sensor and receiver can connect up to
300ft/100m without any obstacles.
• The PIR sensor’s transmitting frequency is
433MHz and its range can be affected by metal,
walls, concretes, and interfering signals from
other electronic appliances with the same
frequency, including televisions, radios, and
cookers.
• Avoid placing the PIR sensor and receiver near to
the above mentioned electronic appliances.
• Do not expose the PIR sensor and receiver to
direct sunlight or high temperatures, otherwise
overheating may cause them irreparably
damaged.
• Do not install the PIR sensor and receiver near
any source of naked flames such as lighted
candles.
• Please test the PIR sensor and receiver at the
potential installation locations before actual
installation to confirm range and transmission
effectiveness.
with the same frequency can also affect the
receiver’s ringing. Avoid mounting the PIR sensor
and receiver near any metal objects.
