manualshive.com logo in svg

1010music Bitbox Micro 1.0.7, User Manual

Share
Download
1010music Bitbox Micro 1.0.7 User Manual Download Page 74

6.

Use the control knobs to select the Amount of modulation that will be applied.
This is used to increase or decrease the amount of impact the modulation will
have on this parameter.

To Use MIDI Learn mode to Modulate Parameters:

You can use a broad range of MIDI controls to modulate some of the pad parameters,
such as Filter and Pitch, and some of the FX parameters, such as Reverb Decay and
Delay Feedback. It can be challenging to determine which MIDI CC number is sent by
any given control on your MIDI device. To make it easier to use these MIDI CCs, bitbox
micro has the ability to learn which control you want to use for modulation for any given
parameter.

To configure a parameter to use a MIDI CC input for modulation:

1.

Connect a MIDI controller to bitbox micro.

2.

Navigate to the pad parameter or FX parameter you want to modulate.

3.

With the parameter selected, push the right arrow button. This brings up the
Modulation Sources screen.

4.

Touch

Learn

in the top right corner to enable MIDI CC learning mode.

5.

Move the MIDI control, such as a knob or slider, that you want to use with this
parameter. When bitbox micro has learned the mapping, the

Learn

button will

turn from blue to gray, and the

Source

parameter will change to

MIDI CC

.

6.

Adjust the

Amount

of modulation you want to allow with this controller.

7.

Now play the pad and use the controller and you will hear the modulation.
The Modulation box associated with this mapping will be labeled

CC

.

To Remove MIDI Modulation from a Parameter:

1.

Go to the Modulation Parameters screens for that parameter.

2.

Scroll to select the Modulation Source you want to clear.

3.

Set the

Source

to none.

Notes:

► The Modulation sources described in this section only impact the pad if the

modulation signal is received on the

MIDI In

channel for this pad.

► Modulation is available for pad and effect parameters.

Copyright 1010music LLC 2020

Page 74 of 88

Bitbox Micro User Manual 1.0.7

Summary of Contents for Bitbox Micro 1.0.7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands