ZyXEL Communications VES-1012 - Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 46

ZyXEL Communications VES-1012 - Скачать руководство пользователя страница 39

VES-1012 Hardware Installation Guide

Appendix A Removing and Installing a Fuse

A

Appendix A

Removing and Installing a Fuse

This appendix shows you how to remove and install fuses for the VES-1012.

The VES-1012 uses two 250V-3A fuses. The VES-1012 comes with four 250V-3A fuses; two are installed at the
factory (in the fuse housing), while the two are spares that come with your VES-1012. If you need to install new
fuses, follow the procedure below.

Before you begin, you will need:

•

A small flat head screwdriver

•

250V 3A fuse(s)

•

Good lighting

Removing and Installing Fuses

Removing Fuses

Safety first! Disconnect all power from the VES-1012 before you begin this procedure.

Step 1.

Place the rear panel of the VES-1012 in front of you.

Step 2.

Remove the power cord from the back of the unit for easy access to the fuse housing as shown next.

Diagram 1 Removing the Power Cord

Step 3.

Using a small flat head screwdriver, gently open the left side of the fuse housing located to the right of
the power cord port as shown next.

«
...
37
38
39
40
41
...
»

Содержание VES-1012 -















































Отзывы:

Нет отзывов