ZyXEL Communications Prestige 128Plus Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 203

ZyXEL Communications Prestige 128Plus Скачать руководство пользователя страница 158

Prestige

128+ ISDN Router

12-2

SNMP Configuration

The following table describes the SNMP configuration parameters.

Table 12-1 SNMP Configuration Menu Fields

Field Description

Default

Get
Community

Enter the get community, which is the password for the incoming
Get- and GetNext- requests from the management station.

public

Set
Community

Enter the set community, which is the password for incoming Set-
requests from the management station.

public

Trusted Host

If you enter a trusted host, your Prestige will only respond to
SNMP messages from this address. If you leave the field blank
(default), your Prestige will respond to all SNMP messages it
receives, regardless of source.

blank

Trap:
Community

Enter the trap community, which is the password sent with each
trap to the SNMP manager.

public

Trap:
Destination

Enter the IP address of the station to send your SNMP traps to.

blank

Once you have completed filling in Menu 22 - SNMP Configuration, press [Enter] at the
message [Press Enter to Confirm] to save your configuration, or press [Esc] to cancel.

«
...
156
157
158
159
160
...
»

Содержание Prestige 128Plus












































































































































































































Отзывы:

Нет отзывов