background image

                                                                                                                   

ZP502 User Manual

 

 

7

2. 

Initial connecting and Setting

 

2.1. Connect the phone 

2.1.1. Connect to network 

Step  1:  Connect  the  IP  Phone  to  the  corporate  IP  telephony  network.  Before  you  connect  the 

phone to the network, please check if your network can work normally.   

 

You can do this in one of two ways, depending on how your workspace is set up.   

 

Direct network connection—by this method, you need at least one available Ethernet port in your 

workspace. Use the Ethernet cable in the package to connect WAN port on the back of your phone 

to the Ethernet port in your workspace. Since this VoIP Phone has router functionality, whether 

you have a broadband router or not, you can make direct network connect. The following two 

figures are for your reference. 

 

 

 

Shared network connection—Use this method if you have a single Ethernet port in your 

workspace with your desktop computer already connected to it. First, disconnect the Ethernet 

cable from the computer and attach it to the WAN port on the back of your phone. Next, use the 

Ethernet cable in the package to connect LAN port on the back of your phone to your desktop 

computer. Your IP Phone now shares a network connection with your computer. The following 

figure is for your reference. 

 

Step 2:    Connect the handset to the handset port by the handset cable in the package. 

Step 3:    connect the power supply plug to the AC 5V adapter port on the back of the phone. Use 

the power cable to connect the power supply to a standard power outlet in your workspace. 

Step 4:    push the on/off switch on the back of the phone to the on side, then the phone’s LCD 

screen displays “Initializing wait logon”. Later, a ready screen typically displays the date, time.   

Содержание ZP502



























































Отзывы: