Zycoo ZP502 Скачать руководство пользователя

Страница: 31 / 58

ZP502 User Manual

interval time less than the NAT server’s.

Enable Via rport

Enable/Disable system to support RFC3581. Via rport is special

way to realize SIP NAT.

Enable PRACK

Enable or disable SIP PRACK function, suggest use the default

config.

Long Contact

Set more parameters in contact field; connection with SEM

server

Enable URI Convert

Convert # to %23 when send the URI.

Dial Without Register

Set call out by proxy without registration;

Ban Anonymous Call

Set to ban Anonymous Call;

Enable DNS SRV

Support DNS looking up with _sip.udp mode

Forward Type

Select call forward mode, the default is Off



Off

：

Close down calling forward



Busy

：

If the phone is busy, incoming calls will be forwarded

to the appointed phone.



No answer

：

If there is no answer, incoming calls will be

forwarded to the appointed phone.



Always

：

Incoming calls will be forwarded to the appoint

phone directly.

The phone will Prompt the incoming while doing forward.

Forward Phone Number

Appoint your forward phone number.

Server Type

Select the special type of server which is encrypted, or has some

unique requirements or call flows.

DTMF Mode

Select DTMF sending mode, there are three modes:



DTMF_RELAY



DTMF_RFC2833



DTMF_SIP_INFO

Different VoIP Service providers may provide different modes.

RFC Protocol Edition

Select SIP protocol version to adapt for the SIP server which uses

the same version as you select. For example, if the server is

CISCO5300, you need to change to RFC2543, else phone may

not cancel call normally. System uses RFC3261 as default.

Transport Protocol

Set transport protocols, TCP or UDP;

RFC Privacy Edition

Set Anonymous call out safely; Support RFC3323and RFC3325;

Subscribe Expire Time

Overtime of resending subscribe packet.

Suggest using the

default config.

Enable Conference number

Set to use sever conference.

MWI Number

Input the number of the server's voice-mail box

Click to Talk

Set click to Talk (need practical software support).

Signal Encode

Enable/Disable Signal Encrypt.

RTP Encode

Enable/Disable RTP Encrypt.

Enable Session Timer

Set Enable/Disable Session Timer, whether support RFC4028.It

will refresh the SIP sessions.

Answer With Single Codec Enable/Disable the function when call is incoming, phone replies

SIP message with just one codec which phone supports.

Содержание ZP502



























































Результаты поиска

Содержание ZP502

Отзывы:

Похожие инструкции для ZP502

Бренды по названию

Популярные бренды

Zycoo ZP502, Руководство пользователя

Результаты поиска

Содержание ZP502

Отзывы:

Похожие инструкции для ZP502

Бренды по названию

Популярные бренды