background image

FV454 Rev C   1/28/13
Page 6

ZURN INDUSTRIES, LLC. 

 COMMERCIAL BRASS OPERATION 

 5900 ELWIN BUCHANAN DRIVE 

 SANFORD NC 27330

Phone: 1-800-997-3876 

 Fax: 919-775-3541 

 World Wide Web: www.zurn.com

In Canada: ZURN INDUSTRIES LIMITED 

 3544 Nashua Drive 

 Mississauga, Ontario L4V1L2 

 Phone: 905-405-8272 Fax: 905-405-1292

®

ZEG6003EV 1/8th Gallon Urinal Parts Breakdown

Parts Identification

1.  Magic Magent
2.  Cover
3.  Lens/Electronics Assembly
4.  Electronics Wedge
5.  Cover O-ring
6.  Electronics Housing Cover
7.  Housing Screw
8.  Cover Screw
9.  Housing (2 sides)
10. Solenoid
11. Solenoid Screw
12. Solenoid Spring
13. Solenoid Plunger
14. Solenoid Diaphragm
15. Solenoid Valve Body
16. Manual Override Plug
17. Manual Override Plug O-ring
18. Manual Override Nut
19. Manual Override Washer
20. Manual Override Seal
21. Manual Override Spring
22. Manual Override O-ring
23. Manual Override Shaft
24. Bottom Plug O-ring
25. Bottom Plug
26. Tailpiece Inner O-ring
27. Tailpiece Nut
28. Tailpiece
29. Tailpiece O-Ring
30. Flow Control
31. Filter
32. Tube Adaptor O-ring
33. Tube Adaptor
34. Tube Adaptor Seal
35. Tube Adaptor Screw
36. Vacuum Breaker Insert
37. Duckbill
38. Vacuum Breaker Tube
39. Vacuum Breaker Tube Nut
40. 3/4" Spud Nut
41. 3/4" Spud Friction Washer
42. 3/4" Spud Sleeve
43. 3/4" Spud Escutcheon
44. Setscrew for Control Stop Cover
45. Vandal-Resistant Control Stop Cover
46. Stop Cap
47. Adjusting Screw
48. Guide Holder
49. Piston Guide
50. Guide O-Ring
51. Piston
52. Piston Seal
53. Stop Body
54. Sweat Solder Adapter
55. Supply Cover Tube

Fl ush C onne ctions and  Spud C oupli ng  Kits Product No.

3/4" Flush Connection and Spud Coupling, 

Items 40-43

P6003-H

Vacuum Breaker Repair Kit, It ems 36-37

P6000-B

Li d and Housing Ki ts

Product No.

1/8 GPF Cover Replacement  Kit , It ems 2-6

PEG6003-L-1-G2

1/8 GPF Housing Replacement  Kit, It ems 7-35

PEG6003-HSA-G2

1/8 GPF Lid O-ring, Item 5

PEG6003-CVR-

ORING-G2

Sol enoid and Valve  Ki ts

Product No.

1/8 GPF Solenoid Repair Kit , Items 12-14

PEG6003-SRK

1/8 GPF Solenoid Replacement Kit, Items 10-11 PEG6003-M
1/8 GPF Filter Replacement Kit , Items 31

PEG6003-FA-G2

Re placem ent Parts and Repair Ki ts

Product No.

1/8 GPF Cover screw, Item 8

PEG6003-CVR-S

C ontrol Stop Re pai r Kit and Parts

Product No.

Control Stop Repair Kit for 1” and 3/4”, 

Includes Items 47-52

PEG6000-D-SD

3/4” Control Stop Replacement, Includes Items 

46-53

PEG6003-C-SD-CP

Seal Seat for 1” and 3/4”, Includes Item 52

P6000-D42

Sweat  Solder Adapter, Includes Item 54

P6003-YBA

Sweat  Kit  and Eschutcheon, Includes It ems 54-

P6003-YBYC

56. Setscrew for Cast Wall Escutcheon
57. Cast Wall Escutcheon
58. Hex Wrench 5/64”
59. Hex Wrench 1/8”

Содержание ZEG6003EV







Отзывы: