ZURN AquaSense Camaya Z6953-XL-W2 Скачать руководство пользователя страница 5

Страница: 5 / 16

FV801 Rev. A 06/21/21

Page 4

2. Install spout to sink using spout base gasket, plastic mounting

washer, star washer and mounting nut.

NOTE

: Before installation, turn off water supplies to existing faucet and remove faucet if replacing an existing device.

Clean the faucet basin and clear away debris. Flush all supply lines before connecting the faucet. Failure to do so

may result in debris clogging the inlets and/or internal control and mixing valve

1. Carefully screw aerator into spout using included tool.

Take care to not pinch blue o-ring

3. Ensure that slot in plastic washer is facing forward.

Sensor cable should pass through the front of the plastic

mounting washer.

Spout Installation Instructions

Z6953-XL-W2

Z6956-XL-W2

Cover Plate Installation Instructions

1. (For faucets with -CP4 or -CP8 suffix).

Pass sensor connector wire and shank through gasket. Align

gasket with faucet bottom and press firmly together. Pass sensor

connector and shank through cover plate and fasten to the faucet

with the provided screws.

Содержание AquaSense Camaya Z6953-XL-W2

















Результаты поиска

Содержание AquaSense Camaya Z6953-XL-W2

Отзывы:

Похожие инструкции для AquaSense Camaya Z6953-XL-W2

Бренды по названию

Популярные бренды

ZURN AquaSense Camaya Z6953-XL-W2, Инструкция по установке, эксплуатации, обслуживанию и каталог запасных частей

Результаты поиска

Содержание AquaSense Camaya Z6953-XL-W2

Отзывы:

Похожие инструкции для AquaSense Camaya Z6953-XL-W2

Бренды по названию

Популярные бренды