Zultys MX250 Скачать руководство пользователя страница 5

Страница: 5 / 62

C h a p t e r 1

Introduction

1.1

Scope

1.1.1

Audience

This manual is intended for properly trained service personnel and technicians who need to

install an MX250 system. The manual assumes you are familiar with electronic circuitry and

wiring practices.

1.1.2

Installation and Use

Unpack the product and verify the items as described in chapter 2, starting on page 7.

Prepare the site as described in chapter 4, starting on page 21.

Warning

The MX250 is designed to be installed by qualified personnel only. Installation by

unqualified individuals may result in injury and damage to the MX250 and

surrounding equipment.

Warning

This equipment is to be installed and maintained by service personnel only as

defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel.

Warning

The MX250 must be installed in a secure location that has access restricted to

qualified personnel only. Placing the MX250 in a location accessible by unqualified

individuals may result in bodily injury and damage to the MX250 and surrounding

equipment.

Install the MX250 as described in chapter 5, starting on page 25.

Install the battery and other accessories as described in the BPS12 Hardware Manual.

Содержание MX250































































Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды

Zultys MX250, Руководство по оборудованию

Результаты поиска

Содержание MX250

Отзывы:

Похожие инструкции для MX250

Бренды по названию

Популярные бренды