Zte AD3812 Скачать руководство пользователя страница 59

Страница: 59 / 71

WCDMA Module

+CMT: <oa>, [<alpha>],<scts>[,<tooa>,<fo>,<pid>,<dcs>,<sca>,<tosca>,

<length>]<CR><LF><data> (text mode enabled; about parameters in italics,
refer command Show

Text Mode ParaCSDH)

If ME has its own display device then class 0 messages and messages in the
message waiting indication group

(discard message) may be copied to both ME display and to TE. In this case,
ME shall send the

acknowledgement to the network (refer table 2).

Class 2 messages and messages in the message waiting indication group
(store message) result in indication as

defined in <mt>=1.

3 Class 3 SMS-DELIVERs are routed directly to TE using unsolicited result
codes defined in <mt>=2. Messages

of other data coding schemes result in indication as defined in <mt>=1.

<bm> (the rules for storing received CBMs depend on its data coding scheme
(refer GSM 03.38 [2]), the setting of

Select CBM Types (+CSCB) and this value; refer table 3):

0 No CBM indications are routed to the TE.

1 If CBM is stored into ME/TA, indication of the memory location is routed to the
TE using unsolicited result

code:

+CBMI: <mem>,<index>

2 New CBMs are routed directly to the TE using unsolicited result code:

+CBM: <length><CR><LF><pdu> (PDU mode enabled)

+CBM: <sn>,<mid>,<dcs>,<page>,<pages><CR><LF><data> (text mode
enabled)

If ME supports data coding groups which define special routing also for
messages other than class 3 (e.g. SIM

specific messages), ME may choose not to route messages of such data coding
schemes into TE (indication of a

stored CBM may be given as defined in <bm>=1).

3 Class 3 CBMs are routed directly to TE using unsolicited result codes defined
in <bm>=2. If CBM storage is

supported, messages of other classes result in indication as defined in <bm>=1.

<ds>:

0 No SMS-STATUS-REPORTs are routed to the TE.

1 SMS-STATUS-REPORTs are routed to the TE using unsolicited result code:

+CDS: <length><CR><LF><pdu> (PDU mode enabled)

+CDS: <fo>,<mr>,[<ra>],[<tora>],<scts>,<dt>,<st> (text mode enabled)

2 If SMS-STATUS-REPORT is stored into ME/TA, indication of the memory
location is routed to the TE using

unsolicited result code:

+CDSI: <mem>,<index>

Содержание AD3812








































































Результаты поиска

Содержание AD3812

Отзывы:

Бренды по названию

Популярные бренды

Zte AD3812, Руководство по управлению

Результаты поиска

Содержание AD3812

Отзывы:

Бренды по названию

Популярные бренды