Zte AD3812 Скачать руководство пользователя страница 38

Страница: 38 / 71

WCDMA Module

2 unknown (e.g. no network, etc.)

<number>: string type phone number of format specified by <type>

<type>: type of address octet in integer format (refer TS 24.008 [8] subclause
10.5.4.7)

<subaddr>: string type subaddress of format specified by <satype>

<satype>: type of subaddress octet in integer format (refer TS 24.008 [8]
subclause 10.5.4.8)

<alpha>: optional string type alphanumeric representation of <number>
corresponding to the entry found in

phonebook; used character set should be the one selected with command
Select TE Character Set +CSCS

<CLI validity>:

0 CLI valid

1 CLI has been withheld by the originator.

2 CLI is not available due to interworking problems or limitations of originating
network.

4.7 +CLIR Calling line identification restriction

Description

This command refers to CLIR-service according to 3GPP TS 22.081 [3] that
allows a calling subscriber to enable or

disable the presentation of the CLI to the called party when originating a call.

Set command overrides the CLIR subscription (default is restricted or allowed)
when temporary mode is provisioned as

a default adjustment for all following outgoing calls. This adjustment can be
revoked by using the opposite command..

If this command is used by a subscriber without provision of CLIR in permanent
mode the network will act according

3GPP TS 22.081 [3].

Read command gives the default adjustment for all outgoing calls (given in <n>),
and also triggers an interrogation of

the provision status of the CLIR service (given in <m>). Test command returns
values supported as a compound value.

+CLIR=[<n>]

+CLIR? +CLIR:

<n>,<m>

Command

+CLIR=?

+CLIR: (list of supported <n>s)

Defined values

<n> (parameter sets the adjustment for outgoing calls):

0 presentation indicator is used according to the subscription of the CLIR
service

1 CLIR invocation

2 CLIR suppression

<m> (parameter shows the subscriber CLIR service status in the network):

0 CLIR not provisioned

Содержание AD3812








































































Результаты поиска

Содержание AD3812

Отзывы:

Бренды по названию

Популярные бренды

Zte AD3812, Руководство по управлению

Результаты поиска

Содержание AD3812

Отзывы:

Бренды по названию

Популярные бренды