background image

CAPACITY CONTROLLERS - 101ALAS

OVERVIEW

The 101ALAS works with the System 2000 Heat Pump System Controller
(101AACBHP).  The 101ALAS provides leaving air temperature readings
to the System Controller, which allows it to make capacity control decisions.

OPERATION

The 101ACBHP System Controller has four status lights that represent
capacity control.  The heat Y1 and Y2 red lights indicate heating opera-
tion and the cool Y1 and Y2 green lights indicate cooling operation.  Heat-
ing or cooling will be initiated depending on the position of the revers-
ing valve. When one of the lights turns on, the leaving air temperature in
the duct, sensed by the LAS, has exceeded one of the capacity control set-
points. The light will indicate which stage will be turned off.  The sec-
ond stage factory default cut-in temperature for heating is 95 degrees, and
for cooling 60 degrees.  If the setpoint is exceeded, a stage light will illu-
minate, the stage will be shut down, and a four-minute time delay will
begin. After the four minute delay, if the leaving air temperature has recov-
ered to an acceptable temperature, the stage which was shut down will
restart.  If the temperature has not recovered, the time delay will contin-
ue.  If both first and second stage setpoints are exceeded by the leaving
air, then a four-minute time delay per stage will go into effect.

MODIFYING SETPOINT ADJUSTMENT

The Heat Pump Controller is designed so that it is possible to modify the
cut-in setpoints for cooling, heating (and electric heat on the Heat Pump
Controller). If necessary, locate the potentiometer associated with its test
point on the diagram above.  “GND” is the common ground test point, TP2

is the cool test point and TP3 is the heat test point. (TP1 is the electric
heat test point on the Heat Pump Controller). Clip the leads of a digital
volt meter, set to 20 volts DC, between the potentiometer test point that
needs to be modified and the ground test point.  Rotate the correspond-
ing potentiometer until the meter reads the proper voltage according
to Table 2 below.

WIRING

The 101ALAS is installed as detailed in the Capacity Controllers
Installation Section, page 40. The + or – terminals of the LAS are
wired to the + or – terminal of the 101AACBHP using two
conductor 18 gauge thermostat wire. 

101AACBHP
HEAT PUMP

CONTROLLER

REV.

VALVE

Y1

Y2

Y1

Y2

HEAT

COOL

J1

ON

PWR

OFF

COOL

HEAT

OFF

AUTO

OFF

ON

AUTO

FAN

Y1

G

Y2

TB2

W

R

O

BL

/

TC2

Y W

B G

Rd

TR1

TR2

S

TB1

TC1

TEMP

+

J2

HEAT ADJ
TP3

COOL ADJ
TP2

ELECTRIC 
HEAT ADJ
TP1

GROUND

GND

101ALAS

+

1

1

LAS VOLTAGE CONVERSION CHARTS

TABLE 1:  CAPACITY CONTROL

TABLE 2:  TEMPERATURE TO VOLTAGE 
CONVERSION CHART

Deg. F.

DC Volts

Deg. F.

DC Volts

Deg. F.

DC Volts

40

2.775

70

2.942

100

3.109

41

2.781

71

2.948

101

3.114

42

2.787

72

2.953

102

3.120

43

2.792

73

2.959

103

3.125

44

2.798

74

2.964

104

3.131

45

2.803

75

2.970

105

3.137

46

2.809

76

2.975

106

3.142

47

2.814

77

2.981

107

3.148

48

2.820

78

2.987

108

3.153

49

2.825

79

2.992

109

3.159

50

2.831

80

2.998

110

3.164

51

2.837

81

3.003

111

3.170

52

2.842

82

3.009

112

3.175

53

2.848

83

3.014

113

3.181

54

2.853

84

3.020

114

3.187

55

2.859

85

3.025

115

3.192

56

2.864

86

3.031

116

3.198

57

2.870

87

3.037

117

3.203

58

2.875

88

3.042

118

3.209

59

2.881

89

3.048

119

3.214

60

2.887

90

3.053

120

3.220

61

2.892

91

3.059

121

3.225

62

2.898

92

3.064

122

3.231

63

2.903

93

3.070

123

3.237

64

2.909

94

3.075

124

3.242

65

2.914

95

3.081

125

3.248

66

2.920

96

3.087

126

3.253

67

2.925

97

3.092

127

3.259

68

2.931

98

3.098

128

3.264

69

2.937

99

3.103

129

3.270

Deg. F.

DC Volts

130

3.275

131

3.281

132

3.287

133

3.292

134

3.298

135

3.303

136

3.309

137

3.314

138

3.320

139

3.325

140

3.331

141

3.337

Cooling 

Second Stage

60

GND & TP2

2.887

Heating 

Second Stage

95

GND & TP3

3.081

Electric Heat

85

GND & TP1

3.025

Discharge Duct 

Temperature

––

LAS + & –

per table #2

STAGE CUT-IN TEMPERATURES*

*The Y2 cut-out temperature is 10° fixed below the cut-in temperature

in cooling, and 10° above in heating.
The Y1 cut-out temperature is 15° fixed below the cut-in temperature in 
cooling, and 25° above in heating.

35

Содержание System 2000

















































Отзывы: