background image

 
 
 

 

                                

CE Declaration of Conformity

 

15

 

Zolix Instruments Co., Ltd.

     

http://www.zolix.com.cn    E-mail:[email protected]

 

 

7  Product quality assurance 

 

Zolix  Instruments  Corporation(Zolix)  certifies  that  the  product  does  not  have  any 

material  and  manufacturing  defects  during  the  warranty  period.  If  there  are  any 

material  or  manufacturing  defects  during  the  warranty  period,  the  company  will  be 

responsible for repairing or replacing the same type of product. 

If artificial operative errors or unauthorized use or unauthorized access to repair or 

natural disasters and other irresistible factors (such as fire, flood, war, etc.), it is not 

within the range of the company's warranty. 

 

 

 

 

 

 

 

 

Manufactured by:

               

  Zolix Instrument Co., Ltd

 

                                                                                           

 

 

 

Applicable Standards: 

Generic Immunity 

       

EN 50082-1 : 1992 

                                               

 

Generic Emission 

                  EN 50081-1 : 1992 

                                                  Electrical Safety Standards 

       

EN 61010-1 : 1993 

 

 

 

 

Zolix Instrument Co., Ltd

 

certifies that this equipment conforms to the protection requirements 

of the above Directives. 

 
 
 
 
 

Содержание GLORIA-X500A




















Отзывы: