manualshive.com logo in svg

ZOJE 1900B, Руководство пользователя, Страница: 53 / 55

Поделиться
Скачать
ZOJE 1900B Скачать руководство пользователя страница 53

 

49 

Position Error 

position. 

the CZ024 at the head signal 

circuit board. 

E 

 

3 0 6 

Thread-catching 

position error 

The thread-catching 

device is at wrong 

position. 

Turn off the power and check 

the CZ026 at the head signal 

circuit board. 

E  3 0 7 

Thread-trimming 

Motor Position 

Error 

The thread-trimming 

motor is not at the right 

position. 

Check the thread-trimming 

device and thread-trimming 

motor to make sure it has no 

blockage. 

E 

 

7 3 3 Motor 

Reverse 

Motor 

Reverse 

Turn off the power and check 

the coupling of the main-shaft 

motor. 

E 

 

8 1 1 Overvoltage 

Error

The voltage of power is 

over the specified 

value. 

Confirm the voltage of power   

E 

 

8 1 3 Low 

Voltage 

Error

The voltage of power is 

too low. 

Confirm the voltage of power. 

E 

 

9 0 1 

Motor driver 

abnormal 

The error is detected in 

motor driver. 

Turn off the power and repower 

the machine after a while. 

E 

 

9 0 3 

Power Supply of 

Pulse Motor Error 

Power supply of the 

pulse motor is not 

output 

Turn off the power and repower 

the machine after a while. 

E 

 

9 0 4 

Solenoid Power 

Supply Error 

Power supply of the 

solenoid cannot output 

Turn off the power and repower 

the machine after a while. 

E 

 

9 0 7 

X Origin Search 

Error 

X origin sensor doesn’t 

change. 

Turn off power and check the 

connections of CZ021 on head 

signal circuit board and X9 on 

control box. 

E 

 

9 0 8 

Y Origin Search 

Error 

Y origin sensor doesn’t 

change. 

Turn off power and check the 

connections of CZ022 on head 

signal circuit board and X9 on 

control box. 

E 

 

9 1 0 

Presser Origin 

Search Error 

Presser origin sensor 

doesn’t change. 

Turn off power and check the 

connections of CZ025 on head 

signal circuit board and X9 on 

control box. 

E  9 1 1 

Y Direction Motor 

Busy 

Y motor doesn’t make 

action according to 

order 

Check the stepping motor in Y 

direction. 

E  9 1 2 

X Direction Motor 

Busy 

X motor doesn’t make 

action according to 

order 

Check the stepping motor in X 

direction. 

Содержание 1900B
























































Отзывы:

Нет отзывов