FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0 FT
.
FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0
FT
.
12
© 2020. All rights reserved.
13
© 2020. All rights reserved.
Wire from
motor
Wire from
power
supply
7
IL1376
Wire from
motor
Pressure
switch
Strain
relief
6
6. Insert an electrical wire strain relief into the
opening in the opposite side of the pressure
switch.
7. Thread the cable from the power supply through
the strain relief and tighten both screws on the
strain relief. Do not crush wire.
Wire
from
motor
Wire from
power
supply
Ground Screws
Green
ground
wire
9
Outside
terminal
Two wires
from power
supply
Outside
terminal
Wire from
motor
Wire from
power
supply
8
9. Connect the green ground wire from the power
supply to the remaining green ground screw in
the pressure switch, and re-attach the pressure
switch cover.
8. Connect the two wires from the power supply to
the two outside terminals on the pressure switch.
A
B
L1
L2
IL2194 B
230 V
GRAY
RED
A
B
L1
L2
IL2195 A
230 V
GRAY
RED
A
B
L1
L2
IL2196 A
115 V
GRAY RED
A B
L1
L2
IL1354 A
115 V
GRAY
RED
C
US
LR90197
UL Std. No. 778
ENCLOSURE 3
starwatersystems.com
Pump:
JHU10
Rev:
B
Motor:
98U1071
HP:
1
PH
1
Hz
60
Volts
115/230
S.F.
1.2
Amps
14/7
S.F. Amps:
14/7
RPM
3450
Type
C
Duty:
Cont.
Temp
65C
KVA Code
G
Frame
56L
Ins Class
B
Factory prewired for 230V
Thermally protected automatically
Check voltage of power source
Use copper conductors only
ELECTRICAL HAZARD
Improper installation may result in fi re, explosion, electrical short or injury. Replace all covers
before operating. Ground motor in accordance with local and national electrical codes.
Disconnect power source before touching internal parts. Motors equipped with automatic
protection may restart without warning.
See instruction manual for proper installation procedure.
Se reporter au manuel d’instructions pour suivre la procédure adéquate d’installation.
Consulte el instructive para conocer el procedimiento de instalación correcto.
L1
L2
A
B
L1
L2
A
B
IL0180
YELLOW
115 VOLT
SINGLE PHASE
LINE
230 VOLT
SINGLE PHASE
LINE
WHITE
GRAY
RED
TAN
YELLOW
WHITE
GRAY
RED
TAN
DATE CODE:
0418*
Made in USA
1
To change from 230 V to 115 V
1. The motor of this pump is dual voltage and can
run on either 115 V or 230 V. In general, 230 V is
more economical to run and requires a smaller
wire size.
NOTE: This pump is pre-wired at the factory to
run on 230 V.
2b
2a
b.
Pull the red wire with the female flag
connector from the “B” terminal. Place it to the
right on the “L2” terminal spade post.
2a. For 115 V service, change the following wires on
the terminal board:
a. Using a pair of needle nose pliers, pull the
gray wire with the female flag connector from
the “B” terminal spade post. Place it to the left
on the “A” terminal spade post.
2c
c. Reinstall the rear motor cover.
NOTE: To change voltage from 115 V to 230 V,
simply reverse instructions above.
230 V
115 V