FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0 FT
.
FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0
FT
.
2
© 2020. All rights reserved.
3
© 2020. All rights reserved.
Power supply required .........................................................................................115 volts or 230 volts, 60 Hz
(Pump is set by the factory to run on 230 volts)
Maximum water temperature .........................................................................................................77°F (25°C)
Individual branch circuit required .......................................................................................... 15 Amp minimum
Discharge connection ........................................................................................................................1 in. NPT
Suction connection ......................................................................................................................1-1/4 in. NPT
Motor duty....................................Continuous duty with enforced air cooling and thermal overload protection
Pressure switch .........................................................................................
Preset at 20 PSI “on” / 40 PSI “off”
Water depth rating - Deep Well ............................................................................................ Maximum of 70 ft
ITEM #
HP VOLTAGE HZ MAX
AMPS
LOCKED
ROTOR
AMPS
PERFORMANCE AT 40 PSI - GPM
DEEP WELL
30 FT 40 FT 50 FT 60 FT 70 FT
1463-0006
1
115/230
60
14/7
52/26
10.6
7.9
7.3
5.7
4.6
• ELECTRICAL SHOCK HAZARD.
Always disconnect power source before performing any work on or near the motor or its connected load.
If the power disconnect point is out-of-sight, lock it in the open position and tag it to prevent unexpected
application of power. Failure to do so could result in fatal electrical shock.
• ELECTRICAL SHOCK HAZARD.
Do not handle the pump with wet hands or when standing in water as fatal electrical shock could occur.
Disconnect main power before handling unit for ANY REASON!
• RISK OF ELECTRIC SHOCK.
These pumps have not been investigated for use in swimming pool areas.
• ELECTRICAL SHOCK ALERT.
Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the
Occupational Safety and Health Act (OSHA).
• ELECTRICAL SHOCK ALERT.
Replace damaged or worn wiring cord immediately. Never use an extension cord.
• ELECTRICAL SHOCK ALERT.
Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces, or
chemicals.
• ELECTRICAL SHOCK ALERT.
Wire motor to correct supply voltage. This pump has a dual voltage motor and can run on 115 V or 230 V. It
is factory pre-set to run on 230 V.
• ELECTRICAL SHOCK ALERT.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the
product.
• NOTE:
Pumps with the “UL” Mark and pumps with the “US” mark are tested to UL Standard UL778.
CSA certified pumps are certified to CSA Standard C22.2 No. 108. (CUS.)
DANGER
WARNING
PRODUCT SPECIFICATIONS
Unit must be securely and adequately electrically grounded. This can be accomplished by wiring the unit to
a ground metal-clad raceway system or by using a separate ground wire connected to the bare metal of the
motor frame or other suitable means.
• ELECTRICAL SHOCK ALERT.
Make certain the electrical power source is adequate for the requirements of the pump.
• ELECTRICAL SHOCK ALERT.
Never use an extension cord with this pump.
• CHEMICAL ALERT.
Prop65 Warning for California residents:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
• HAZARDOUS PRESSURE ALERT.
Install pressure relief valve in discharge pipe. Release all pressure on system before working on any
component.
• EXPLOSION ALERT
Do not use to pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not use in
flammable and/or explosive atmospheres.
• PRODUCT DAMAGE MAY RESULT
This pump is not to be used for irrigation or water systems.
• PRODUCT DAMAGE MAY RESULT
Protect the power cable from coming in contact with sharp objects.
• PRODUCT DAMAGE MAY RESULT
Do not run pump dry.
• PRODUCT DAMAGE MAY RESULT
Pump and plumbing must be full of water before startup.
• PRODUCT DAMAGE MAY RESULT
Do not pump water which contains sand, mud, silt, or debris.
• INJURY MAY RESULT
Be careful when touching the exterior of an operating motor. It may be hot enough to be painful or cause
injury.
CAUTION
CAUTION
Description
Quantity
A
Pump
1
B
Ejector
1
C
Gasket
1
D
Bolts
2
E
20/40 Pressure Switch
1
F
Control Body
1
G Control Body Adjustment Screw
1
H
Strain Relef
1
I
1” x 3/4” PVC Adapter
1
PACKAGE CONTENTS
IL0194
A
B
C
D
E
F
G
I
H
