FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0 FT
.
FOR
DEEP
WELL
APPLICA
TIONS
2
5 -
7
0
FT
.
18
© 2020. All rights reserved.
19
© 2020. All rights reserved.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Little or no
discharge
1. Casing not initially filled with water
1. Fill pump casing
2. Suction lift too high, or too long
2. Move pump closer to water source
3. Hole or air leak in suction line
3. Repair or replace. Use pipe tape and
pipe sealing compound.
4. Foot valve too small
4. Match foot valve to piping or install one
size larger foot valve.
5. Foot valve or suction line not submerged
deep enough in water
5. Submerge lower in water
6. Motor wired incorrectly
6. Check wiring diagram
7. Casing gasket leaking
7. Replace
8. Suction or discharge line valves closed
8. Open
Pump will not
deliver water
or develop
pressure
1. No priming water in casing
1. Fill pump casing
2. Leak in suction line
2. Repair or replace
3. Discharge line is closed, and priming air
has nowhere to go
3. Open ball valve
4. Suction line (or valve) is closed
4. Open
5. Foot valve is leaking
5. Replace foot valve
6. Suction screen clogged
6. Clean or replace
Loss of suction
1. Air leak in suction line
1. Repair or replace
2. Suction lift too high
2. Lower suction lift, install foot valve, and
prime
3. Insufficient inlet pressure or suction head
3. Increase inlet pressure by adding more
water to tank or increasing back pressure
4. Clogged foot valve or strainer
4. Unclog
Pump vibrates
and/or makes
excessive noise
1. Mounting plate or foundation not rigid
enough
1. Reinforce
2. Foreign material in pump
2. Disassemble pump and clean
3. Impeller damaged
3. Replace
4. Worn motor bearings
4. Replace
Pump will not
start or run
1. Improperly wired
1. Check wiring diagram on motor
2. Blown fuse or open circuit breaker
2. Replace fuse or close circuit breaker
3. Loose or broken wiring
3. Tighten connections, replace broken
wiring
4. Stone or foreign object lodged in impeller 4. Disassemble pump and remove foreign
object
5. Motor shorted out
5. Replace
6. Thermal overload has opened circuit
6. Allow unit to cool. Restart after reason for
overload has been determined.
WARRANTY
REPAIR PARTS
ITEM
DESCRIPTION
PART NO.
1
Repair Kit includes
impeller, diffuser, rotary
seal, quadraseal, and
diffuser rubber
148140
2
Flow Control Assembly
134349
7
8
This product is warranted for two years from the date of purchase. Subject to the conditions hereinafter set
forth, the manufacturer will repair or replace to the original consumer any portion of the product which proves
defective due to defective materials or workmanship. To obtain warranty service, contact the dealer from whom
the product was purchased. The manufacturer retains the sole right and option to determine whether to repair
or replace defective equipment, parts, or components. Damage due to conditions beyond the control of the
manufacturer is not covered by this warranty.
THIS WARRANTY WILL NOT APPLY: (a) To defects or malfunctions resulting from failure to properly install,
operate, or maintain the unit in accordance with printed instructions provided; (b) to failures resulting from
abuse, accident, or negligence, or use of inappropriate chemicals or additives in the water; (c) to normal
maintenance services and the parts used in connection with such service; (d) to units which are not installed
in accordance with normal applicable local codes, ordinances, and good trade practices; and (e) if the unit is
used for purposes other than for what it was designed and manufactured.
RETURN OF WARRANTED COMPONENTS: Any item to be repaired or replaced under this warranty must be
returned to the manufacturer at Kendallville, Indiana or such other place as the manufacturer may designate,
freight prepaid.
THE WARRANTY PROVIDED HEREIN IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND MAY
NOT BE EXTENDED OR MODIFIED BY ANYONE. ANY IMPLIED WARRANTIES SHALL BE LIMITED TO
THE PERIOD OF THE LIMITED WARRANTY AND THEREAFTER ALL SUCH IMPLIED WARRANTIES ARE
DISCLAIMED AND EXCLUDED. THE MANUFACTURER SHALL NOT, UNDER ANY CIRCUMSTANCES, BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO
DAMAGE TO, OR LOSS OF, OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFITS, INCONVENIENCE,
OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY TYPE OR NATURE. THE LIABILITY
OF THE MANUFACTURER SHALL NOT EXCEED THE PRICE OF THE PRODUCT UPON WHICH SUCH
LIABILITY IS BASED.
This warranty gives you specific legal rights, and you may have other rights which vary from state to
state. Some states do not allow limitations on duration of implied warranties or exclusion of incidental or
consequential damages, so the above limitations may not apply to you.
1
2
In those instances where damages are incurred as a result of an alleged pump failure, the Homeowner
must retain possession of the pump for investigation purposes.
