background image

7.4  Control Box Error Codes (VX45 4WD, VX50 4WD and VX55 4WD)

 

The control box will display one of ten different error codes to indicate specific problems with either the control box or 

mechanically with the cleaner. 

•  To remove an error code after troubleshooting, press any key and the control box turns off.

•  If an error code is displayed and no key pressed, the screen goes into standby mode after 10 minutes of inactivity. 

Press any key to turn the screen back on.

•  When an error is detected, programming for the control box is temporarily suspended. The 

 button is 

turned off.  

Press and hold the 

 button to clear the error code and reactivate current programming.

Error Code

Cause

•  Solution

1

2

3

(1) Pump short-circuit.

(2) Right side traction motor  

short-circuit

(3) Left side traction motor  

short-circuit

•  Check for any small debris or floating cable 

stopping brushes from turning freely.

•  Check the connector pins in the floating cable 

for corrosion or a bent pin.

•  Turn each wheel one quarter turn in one 

direction repeatedly until rotation is smooth and 

not catching, then repeat turning wheel in the 

opposite direction until rotation is smooth. 

•  If problem is not resolved through 

troubleshooting, contact Zodiac After Sales 

Support at 1300 763 021.

4

Pump motor overconsumption

•  Check for small debris or hair in the fan. 

•  Clean the filter canister.

5

6

(5) Right side drive motors 

overconsumption

(6) Left side drive motors 

overconsumption

•  Check for any small debris or hair and that the 

floating cable is not caught, stopping brushes 

from turning freely. 

•  Turn each wheel one quarter turn in one 

direction repeatedly until rotation is smooth and 

not catching, then repeat turning wheel in the 

opposite direction until rotation is smooth.

7

8

(7) Cleaner floats on the surface.

(8) Cleaner is turned on and running 

out of water.

•  Turn cleaner power off, then submerge cleaner  

according to correct procedure. 

9

NOT A CLEANER ERROR

•  End of cycle status code. Cleaner function is 

normal. No action required.

10

Cleaner and control box 

communication error.

•  Turn cleaner power off then back on to restart 

the program.

•  Check connection of the floating cable on the 

control box. 

•  Check the connector pins in the floating cable 

for corrosion or a bent pin.

•  If problem is not resolved through 

troubleshooting, contact Zodiac After Sales 

Support at 1300 763 021.

  

 

23 

H0516700_REV C

Содержание VORTEX-PRO EC15 Series

























Отзывы: